MAX2041ETP+ Maxim Integrated Products, MAX2041ETP+ Datasheet - Page 13

• Manufacturer Part Number: MAX2041ETP+
• Description: Up-Down Converters IC MIXER UP/DWN HI LIN
• Manufacturer: Maxim Integrated Products

Specifications of MAX2041ETP+

• Maximum Input Frequency: 3000 MHz
• Maximum Power Dissipation: 2200 mW
• Maximum Operating Frequency: 350 MHz
• Maximum Power Gain: - 7.1 dB
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Package / Case: TQFN-20 EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

be applied to V
LOSEL (see the Absolute Maximum Ratings). LO1 and
LO2 inputs are internally matched to 50Ω, requiring
only a 22pF DC-blocking capacitor.
A two-stage internal LO buffer allows a wide-input power
range for the LO drive. The on-chip low-loss balun,
along with an LO buffer, drives the double-balanced
mixer. All interfacing and matching components from
the LO inputs to the IF outputs are integrated on chip.
The core of the MAX2041 is a double-balanced, high-
performance passive mixer. Exceptional linearity is pro-
vided by the large LO swing from the on-chip LO buffer.
The MAX2041 mixer has an IF frequency range of DC to
350MHz. Note that these differential ports are ideal for
providing enhanced IIP2 performance. Single-ended IF
applications require a 1:1 balun to transform the 50Ω dif-
ferential IF impedance to a 50Ω single-ended system.
After the balun, the IF return loss is better than 15dB.
The differential IF is used as an input port for upconvert-
er operation. The user can use a differential IF amplifier
following the mixer but a DC block is required on both IF
pins. In this configuration, the IF+ and IF- pins need to
be returned to ground through a high resistance (about
1kΩ). This ground return can also be accomplished by
grounding the RF TAP (pin 3) and AC-coupling the IF+
and IF- ports (pins 19 and 18).
The RF and LO inputs are internally matched to 50Ω. No
matching components are required. Return loss at the RF
port is typically better than 17dB over a 1400MHz to
3000MHz frequency range, and return loss at the LO
ports is typically better than 16dB over a 1900MHz to
3000MHz frequency range. RF and LO inputs require
only DC-blocking capacitors for interfacing.
The IF output impedance is 50Ω (differential). For eval-
uation, an external low-loss 1:1 (impedance ratio) balun
transforms this impedance to a 50Ω single-ended out-
put (see the Typical Application Circuit).
Bias current for the LO buffer is optimized by fine tun-
ing resistor R1. If reduced current is required at the
expense of performance, contact the factory for details.
If the ±1% bias resistor values are not readily available,
substitute standard ±5% values.
High-Linearity, 1700MHz to 3000MHz Upconversion/
Downconversion Mixer with LO Buffer/Switch
Applications Information
CC
______________________________________________________________________________________
before digital logic is applied to
Input and Output Matching
High-Linearity Mixer
Differential IF
Bias Resistor
A properly designed PC board is an essential part of
any RF/microwave circuit. Keep RF signal lines as short
as possible to reduce losses, radiation, and induc-
tance. For the best performance, route the ground pin
traces directly to the exposed pad under the package.
The PC board exposed pad MUST be connected to the
ground plane of the PC board. It is suggested that mul-
tiple vias be used to connect this pad to the lower-level
ground planes. This method provides a good RF/ther-
mal conduction path for the device. Solder the exposed
pad on the bottom of the device package to the PC
board. The MAX2041 Evaluation Kit can be used as a
reference for board layout. Gerber files are available
upon request at www.maxim-ic.com.
Proper voltage-supply bypassing is essential for high-
frequency circuit stability. Bypass each V
TAP with the capacitors shown in the Typical
Application Circuit; see Table 1. Place the TAP bypass
capacitor to ground within 100 mils of the TAP pin.
The EP of the MAX2041’s 20-pin thin QFN-EP package
provides a low thermal-resistance path to the die. It is
important that the PC board on which the MAX2041 is
mounted be designed to conduct heat from the EP. In
addition, provide the EP with a low-inductance path to
electrical ground. The EP MUST be soldered to a
ground plane on the PC board, either directly or
through an array of plated via holes.
Table 1. Component List Referring to the
Typical Application Circuit
C3, C5, C9, C11
C2, C6, C7, C8,
COMPONENT
Exposed Pad RF/Thermal Considerations
C10, C12
C1
C4
U1
R1
T1
MAX2041 Maxim IC
1:1 Balun
VALUE
0.01µF
549Ω
10pF
22pF
4pF
Power-Supply Bypassing
Layout Considerations
Microwave capacitor (0603)
Microwave capacitor (0603)
Microwave capacitors (0603)
Microwave capacitors (0603)
±1% resistor (0603)
IF balun with DC grounded
ports
M/A-COM MABAES0029
DESCRIPTION
CC
pin and
13