TDA9887TS/V4 NXP Semiconductors, TDA9887TS/V4 Datasheet - Page 35

• Manufacturer Part Number: TDA9887TS/V4
• Description: RF Receiver DEMODULATOR VIF AND SIF
• Manufacturer: NXP Semiconductors
• Type: Transmitter/Receiverr

Specifications of TDA9887TS/V4

• Package / Case: SSOP-24
• Operating Frequency: 58.75 MHz
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: - 20 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: TDA9887TS/V4,112

Philips Semiconductors
Notes
1. Values of video and sound parameters can be decreased at V
2. Level headroom for input level jumps during gain control setting.
3. This parameter is not tested during the production and is only given as application information for designing the
4. Loop bandwidth BL = 70 kHz (damping factor d = 1.9; calculated with sync level within gain control range).
5. V
6. Condition: luminance range (5 steps) from 0 % to 100 %.
7. S/N is the ratio of black-to-white amplitude to the black level noise voltage (RMS value on pin CVBS). B = 5 MHz
8. The intermodulation figures are defined for:
2004 Aug 25
I
f
V
V
I
I
V
I
I
Output ports (pins OP1 and OP2); note 32
V
V
I
I
2
SCL
IH
IL
o(sink)
o(source)
o(sink)
o(sink/source)(max)
IH
IL
OL
OL
OH
C-bus transceiver (pins SDA and SCL); notes 30 and 31
I
IF-PLL demodulator with FM radio
2
receiver circuit.
Calculation of the VIF-PLL filter can be done by use of the following formula:
where:
K
R is the loop resistor; C is the loop capacitor; BL
modulation.
(B/G, I and D/K standard). Noise analyzer setting: 200 kHz high-pass and SC-trap switched on.
a) f = 1.1 MHz (referenced to black and white signal) as
b) f = 3.3 MHz (referenced to colour carrier) as
BL
d
SYMBOL
C-bus controlled multistandard alignment-free
O
i(VIF)
=
–
is the VCO steepness
3dB
1
-- - R K
2
= 10 mV (RMS); f = 1 MHz (VCO frequency offset related to picture carrier frequency); white picture video
=
------ - K
2
1
O
K
D
O
SCL clock frequency
HIGH-level input voltage
LOW-level input voltage
HIGH-level input current
LOW-level input current
LOW-level output voltage
output sink current
output source current
LOW-level output voltage
HIGH-level output voltage
output sink current
maximum output sink or source
current
C
K
D
,
R
, valid for d
PARAMETER
rad
------- -
V
or
1.2
2
Hz
------ -
V
; K
D
is the phase detector steepness
3dB
I
V
V
I
current)
pin OP2 functions as
VIF-AGC output
IM
OL
OL
P
P
= 0 V
= 0 V
is the loop bandwidth for 3 dB; d is the damping factor.
= 3 mA
= 2 mA (sink
=
35
CONDITIONS
20
IM
log
=
P
V
-------------------------------------
V
= 4.5 V.
20
0
0
at 4.4 MHz
at 3.3 MHz
log
V
-------------------------------------
V
0
0
0
3
at 4.4 MHz
at 1.1 MHz
0.3
10
10
MIN.
------- -
rad
A
TYP.
+
;
3.6 dB
Product specification
400
V
+1.5
+10
+10
0.4
10
10
0.4
6
2
10
MAX.
CC
TDA9887
kHz
V
V
V
V
V
mA
A
A
A
A
A
UNIT