FYH0H105ZF Renesas Electronics America, FYH0H105ZF Datasheet - Page 2

• Manufacturer Part Number: FYH0H105ZF
• Manufacturer: Renesas Electronics America

Specifications of FYH0H105ZF

• Lead Free Status / RoHS Status: Supplier Unconfirmed

●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
Specifi cations
Item
Category temperature range
MAX operating voltage
Capacitance
Capacitance allowance
ESR
Current (30-minutes value)
Surge
Characteristics in
different temperature
Lead strength (tensile)
Vibration resistance
Solderability
Solder heat resistance
Temperature cycle
High temp. and high
humidity resistance
High temperature load
Self discharge characteristics
(voltage holding characteristics)
Capacitance
ESR
Current (30 minutes value)
Appearance
Capacitance
ESR
Capacitance
ESR
Capacitance
ESR
Current (30 minutes value)
Capacitance
ESR
Current (30 minutes value)
Capacitance
ESR
Current (30 minutes value)
Appearance
Capacitance
ESR
Current (30 minutes value)
Appearance
Capacitance
ESR
Current (30 minutes value)
Appearance
Capacitance
ESR
Current (30 minutes value)
Appearance
Capacitance
ESR
Current (30 minutes value)
Appearance
Series name
−25 ℃ to ＋70 ℃
5.5Vdc
Refer to standard ratings
＋80 ％, −20 ％
FYD ：0.022F to 2.2F
FYH ：0.022F to 1.0F
FYL ：0.010F to 0.047F
Refer to standard ratings
More than 90% of initial ratings
Not to exceed 120% of initial ratings
Not to exceed 120% of initial ratings
No obvious abnormality
No terminal damage
Satisfy initial ratings
No obvious abnormality
Over 3/4 of the terminal should be covered by
the new solder
Satisfy initial ratings
No obvious abnormality
Satisfy initial ratings
No obvious abnormality
Within ±20% of initial value
Not to exceed 120% of initial ratings
Not to exceed 120% of initial ratings
No obvious abnormality
Within ±30% of initial value
Below 200% of initial ratings
Below 200% of initial ratings
No obvious abnormality
Voltage between terminal leads higher than 4.2V
Phase 2
Phase 3
Phase 5
Phase 6
FY type (FYD, FYH, FYL)
50% or higher than initial value
400% or less than initial value
200% or less than initial value
Satisfy initial ratings
1.5CV (mA) or below
Within ±20% of initial value
Satisfy initial ratings
Satisfy initial ratings
Refer to Measurement Conditions
Refer to Measurement Conditions
Measured at 1kHz, 10mA ; See also Measurement
Conditions
Refer to Measurement Conditions
Surge voltage ：6.3V
Charge：30 sec.
Discharge：9min 30sec.
Number of cycles：1000
Series resistance ：0.010F
Discharge resistance：0Ω
Temperature：70±2 ℃
Conforms to 4.17
Phase1：＋25±2 ℃
Phase2：−25±2 ℃
Phase4：＋25±2 ℃
Phase5：＋70±2 ℃
Phase6：＋25±2 ℃
Conforms to 4.9
Conforms to 4.13
Frequency：10 to 55 Hz
Testing time：6 hours
Conforms to 4.11
Solder temp：245±5 ℃
Dipping time：5±0.5 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.10
Solder temp：260±10 ℃
Dipping time：10±1 sec.
1.6mm from the bottom should be dipped.
Conforms to 4.12
Temperature condition：−25 ℃ →Room temperature→
Number of cycles：5 Cycles
Conforms to 4.14
Temperature：40±2 ℃
Relative humidity：90 to 95 ％RH
Testing time：240±8 hours
Conforms to 4.15
Temperature：70±2 ℃
Voltage applied：MAX operating voltage
Series protection resistance：0Ω
Testing time：1000
Charging
condition
Storage
Test conditions (conforming to JIS C 5160-1)
Super Capacitors Vol.12 25
Voltage applied：5.0Vdc (Terminal
at the case's side be negative)
Series resistance：0Ω
Charging time：24 hours
Let stand for 24 hours in condition
described below with terminals opened.
Ambient temperature：Lower than 25 ℃
Relative humidity：Lower than 70%RH
：0.022F
：0.047F
：0.068F
：0.10F
：0.22F
：0.47F
：1.0F, 1.4F
：2.2F
＋48
0
Hours
＋70 ℃ →Room temperature
2010.11.8 9565SCAVOL12E
1500Ω
560Ω
300Ω
240Ω
150Ω
56Ω
30Ω
15Ω
10Ω