DEMO908QC16 Freescale, DEMO908QC16 Datasheet

no-image

DEMO908QC16

Manufacturer Part Number
DEMO908QC16
Description
Manufacturer
Freescale
Datasheet
1.DEMO908QC16.pdf (3 pages)

Specifications of DEMO908QC16

Architecture
8/16-bit
Code Gen Tools Included
Code Warrior
Lead Free Status / RoHS Status
Not Compliant
Freescale Semiconductor
Quick Start Guide
DEMO908QC16 Quick Start Guide
Introduction and Default Settings
This kit contains everything you need to get started. This guide will walk you though how to connect the board to
your PC, install the correct version of CodeWarrior Development Studio, run the PWU (periodic wakeup module)
test program, and load an ATD (analog-to-digital) test program. Source code for DEMO908QC16_PWU and
DEMO908QC16_ATD (ATD test) are provided on the Axiom CD in the “Examples” folder.
Figure 1
User’s Guide on the Axiom CD for information on other configurations. Black blocks indicate the “on” or “installed”
position of jumpers. Please check the settings before continuing.
Install CodeWarrior Development Studio Version 5.0 for HC(S)08
If you do not have version 5.0 of CodeWarrior for HC(S)08 installed on your computer, please refer to the provided
“CodeWarrior Development Studio” DVD case and follow the steps in the quick start guide.
Run the DEMO908QC16_PWU Program
The DEMO908QC16 is shipped with the DEMO908QC16_PWU test program stored in on-chip FLASH memory.
You may view the source code for this program by accessing the “DEMO908QC16_PWU.zip” file on the Axiom CD
(located in the “Examples” folder).
© Freescale Semiconductor, Inc., 2005. All rights reserved.
1.
2.
3.
Check the jumper settings and make sure they are in the default position. Use
Connect the USB cable to the PC and then the board. If you are using this board for the first time, please
follow the instructions on the screen to install the USB device properly.
After the USB drivers are installed correctly, the USB LED, PWR OUT, and +5V LED will be on.
illustrates the default settings for the DEMO908QC16 demo board. Please refer to the DEMO908QC16
PWR_SEL
COM_SEL
LIN
PWR
VB
COM
Figure 1. DEMO908QC16 Default Settings
OSC_EN
VX_EN
USB-MON08 ENABLE
D
C
B
E
F
J
I
Figure 1
DEMO908QC16QSG
Rev. 0.02, 1/2006
as a guide.

DEMO908QC16 Summary of contents

Page 1

... Development Studio” DVD case and follow the steps in the quick start guide. Run the DEMO908QC16_PWU Program The DEMO908QC16 is shipped with the DEMO908QC16_PWU test program stored in on-chip FLASH memory. You may view the source code for this program by accessing the “DEMO908QC16_PWU.zip” file on the Axiom CD (located in the “Examples” folder). 1. ...

Page 2

... The USB-MON08 allows a user to program the MCU FLASH and debug application via USB connection the Axiom CD (“Examples” folder), copy the “DEMO908QC16_ATD.zip” file to your PC, open, and extract the files into a working folder on your desktop. Note: Be sure to extract, and not just copy, the files. ...

Page 3

... Make sure all the jumpers on the USB-MON08 ENABLE header are installed. Refer to • Make sure USER_EN jumpers RV1 and RZ1 are not installed. Unable to Run the ATD program correctly: • Make sure USER_EN jumper RZ1 is installed. Freescale Semiconductor DEMO908QC16 Quick Start Guide, Rev. 0.02 Troubleshooting Figure 2. 3 ...