125800D00000G Aavid Thermalloy, 125800D00000G Datasheet - Page 101
![no-image](/images/no-image-200.jpg)
125800D00000G
Manufacturer Part Number
125800D00000G
Description
SOLDER ANCHOR FOR BGA HEATSINKS
Manufacturer
Aavid Thermalloy
Datasheet
1.125700D00000G.pdf
(116 pages)
Specifications of 125800D00000G
Accessory Type
Solder Anchor (2 required)
Packages Cooled
BGA
Length
7.62mm
Rohs Compliant
Yes
For Use With/related Products
Heat Sinks
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
43409
Thermalfilm™ Polyimide Plastic Films
Thermalfilm™ and Thermalfilm™ MT are low cost polymide plastic insulating films designed
to be an improved replacement for mica. These insulators have a distinctive amber color and
can be easily recognized and assembled on a production line.
Thermalfilm™ MT, made from high performance Kapton™ MT material, provides thermal
conductivity nearly 2-5 times greater than standard Thermalfilm™. Both insulators have an
extremely high resistance to flow or thin out under high compressive stresses, particularly at
elevated temperatures. Excellent physical, mechanical and electrical properties remain nearly
constant over a wide range of temperatures and frequencies. They are radiation resistant,
have no melting points, and have no known organic solvents. The polymide plastic film is UL
listed as a component in UL’s publication “Component – Plastic Material” dated September
18, 1969. The UL card number is E39505R, Guide QMFZ2 filed by E. I. du Pont de Nemours
& Co., Inc. Thermalfilm
ORDERING INFORMATION
For standard pre-cut sizes of Thermalfilm
and Thermafilm
www.aavidthermalloy.com
PROPERTY
Dielectric strength
Dielectric constant
Dissipation factor
Volume resistivity
Surface resistivity
Corona start voltage 0.025mm (1-mil)
Insulation resistance
Material thickness
Ultimate tensile strength (MD)
Bursting strength test (Mullen)
Tear strength – initial
Density
Folding endurance (MIT)
Melting point
Zero strength temperature
Cut through temperature
Service temperature
Thermal conductivity
Flammability
Notes: One mil equals 0.001 inch
Dimensional tolerances are ± 0.38mm (0.015”), hole diameters are ± 0.25mm (0.010”) and angularity is ± 1 1/2° unless otherwise specified.
TM
MT see page 102.
TM
is rated 94-V/0.
AMERICA
EUROPE
TM
Italy Tel: +39 051 764011 email: sales.it@aavid.com
United Kingdom Tel: +44 1793 401400 email: sales.uk@aavid.com
USA Tel: +1 (603) 224-9988 email: info@aavid.com
Italy Tel: +39 051 764011 email: sales.it@aavid.com
United Kingdom Tel: +44 1793 401400 email: sales.uk@aavid.com
USA Tel: +1 (603) 224-9988 email: info@aavid.com
THERMALFILM™
0.03mm (1-mil)
240 x 10
(6,100 volts/mil)
3.5
0.002
10
10
465 volts
100.000 megohm mfds.
0.05mm (0.002”)
1.72 x 10
3.10 x 10
27,559 gm/mm (700 gm/mil)
1.42 gm/cm
>10,000 cycles
NONE
815
435
525
-260
(-436
0.156W/m
(0.09 BTU/hr-ft-ºF)
V-0, UL “E” card E39505
17
16
º
º
º
C (1499
C (815
C (977
ohm-cm
ohms
º
C to 240
º
F to 464
3
8
5
volts/mm
Pa (25,000 psi)
Pa (45 psi)
º
º
F)
F)
º
ELECTRICAL – TYPICAL VALUE @ 25° C
C
º
3
F)
(88.7 lb/ft
º
C
º
F)
3
)
PHYSICAL
THERMAL
THERMALFILM™ MT
177.2 x 10
(4500 volts/mm)
4.3
0.002
10
10
465 volts
100.000 megohm mfds.
0.05mm (0.002”)
103 MPa (1500 psi)
0.31 MPa (45 psi)
35,433 gm/mm (900 gm/mil)
1.78 gm/cm
>10,000 cycles
NONE
815
435
525
-260
(-436
0.379 W/m
(0.219 BTU/hr-ft-
V-0, UL “E” card E39505
Thermalfilm™ and Thermalfilm™ MT
17
16
º
º
º
C (1499
C (815
C (977
ohm-cm
ohms
º
C to 240
º
F to 464
3
º
º
F)
F)
volts/mm
º
º
C
3
F)
(111.1 lb/ft
º
C
º
F)
ASIA
º
F)
Singapore Tel: +65 6362 8388 email: sales@aavid.com.sg
Taiwan Tel: +886 (2) 2698-9888 email: sales@aavid.com.tw
3
)
TEST METHOD
ASTM D149-64
ASTM D150-64T
ASTM D150-64T
ASTM D257-61
ASTM D257-61
ASTM D1868-61T
Based on 0.05 mfd wound
capacitor using 0.25 mm
(1-mil) Film
ASTM D882-64T
ASTM 0774-63
ASTM D1004-61
ASTM D1505-63T
ASTM D2176-63T
Hot Bar (Du Pont test)
Weighted probe on heated film
(Du Pont test)
Model TC-1000 twin heatmeter
Comparative tester
UL 94
101