M36W0R6040T7ZAQE NUMONYX, M36W0R6040T7ZAQE Datasheet
M36W0R6040T7ZAQE
Specifications of M36W0R6040T7ZAQE
Available stocks
Related parts for M36W0R6040T7ZAQE
M36W0R6040T7ZAQE Summary of contents
Page 1
... OTP cells – 64-bit unique device number Common flash interface (CFI) 100,000 program/erase cycles per block PSRAM Access time Low standby current: 70 μA Deep power-down current: 10 μA Table 1. Device summary M36W0Rx0x0x7 M36W0R5030T7 M36W0R5040T7 M36W0R6040T7 209220 - Rev 3 FBGA M36W0R5030B7 M36W0R5040B7 M36W0R6040B7 1/24 www.numonyx.com 1 ...
Page 2
Contents Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 3
M36W0Rx0x0x7 8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
List of tables List of tables Table 1. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 5
M36W0Rx0x0x7 List of figures Figure 1. Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 6
Description 1 Description The M36W0R5030x7, M36W0R5040x7, and M36W0R6040x7 combine two memory devices in a multichip package: a 32- or 64-Mbit, multiple bank flash memory, the M58WR032KT/B or M58WR064KT/B, respectively 16-Mbit PSRAM, the M69KB012AB or M69KB024AB, respectively. Recommended ...
Page 7
M36W0Rx0x0x7 Figure 1. Logic diagram 1. Amax is equal to A20 in the M36W0R50x0x7 and A21 in the M36W0R6040x7 DDQ PPF V DDF 22 (1) A0-Amax M36W0R5030x7 F M36W0R5040x7 ...
Page 8
Description Table 2. Signal names Name A0-A18 DQ0-DQ15 V DDF V DDQ V PPF CCP NC DU Flash memory control functions A19-A20, A20, or (2) A20-A21 WAIT F W ...
Page 9
M36W0Rx0x0x7 Figure 2. TFBGA connections (top view through package ...
Page 10
Signal descriptions 2 Signal descriptions See Figure 1: Logic diagram connected to this device. 2.1 Address inputs (A0-A21) Addresses A0-A18 are common inputs for the flash memory and PSRAM components. The address inputs select the cells in the memory array ...
Page 11
M36W0Rx0x0x7 2.6 Flash Write Protect (WP Write Protect is an input that gives an additional hardware protection for each block. When Write Protect is Low, V blocks cannot be changed. When Write Protect is at High, V the locked-down blocks ...
Page 12
Signal descriptions 2.12 PSRAM Output Enable (G The Output Enable, G cycles to be achieved with the common I/O data bus. 2.13 PSRAM Write Enable (W The Write Enable, W 2.14 PSRAM Upper Byte Enable (UB The Upper Byte Enable, ...
Page 13
M36W0Rx0x0x7 2.19 V program supply voltage PPF V is both a flash memory control input and a flash memory power supply pin. The two PPF functions are selected by the voltage range applied to the pin kept ...
Page 14
Functional description 3 Functional description The flash memory and PSRAM components have separate power supplies but share the same grounds. They are distinguished by two Chip Enable inputs: E and E for the PSRAM. P Recommended operating conditions do not ...
Page 15
M36W0Rx0x0x7 Figure 3. Functional block diagram A19-20 (1) or A20 (2) or A20-A21 A0-A18 (1) (2)(3) or A0-A19 1. Address inputs corresponding to the M36W0R5030x7 devices. 2. Address inputs corresponding to the M36W0R5040x7 devices. 3. Address inputs corresponding to the ...
Page 16
Functional description Table 3. Main operating modes Operation Flash read Flash write Flash address latch Flash output ...
Page 17
M36W0Rx0x0x7 4 Maximum ratings Stressing the device above the rating listed in cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating ...
Page 18
DC and AC parameters 5 DC and AC parameters This section summarizes the operating measurement conditions, and the DC and AC characteristics of the device. The parameters in the DC and AC characteristics tables in this section are derived from ...
Page 19
M36W0Rx0x0x7 Figure 5. AC measurement load circuit Table 6. Device capacitance Symbol C Input capacitance IN C Output capacitance OUT 1. Sampled only, not 100% tested. Please refer to the M58WR032KT/B and M58WR064KT/B and M69KB012AB or M69KB024AB datasheets for further ...
Page 20
... Package mechanical 6 Package mechanical To meet environmental requirements, Numonyx offers the M36W0R50x0x7 and M36W0R6040x7 in RoHS compliant packages, which have a lead-free second-level interconnect. In compliance with JEDEC standard JESD97, the category of second-level interconnect is marked on the package and on the inner box label. The maximum ratings related to soldering conditions are also marked on the inner box label ...
Page 21
M36W0Rx0x0x7 Table 7. Stacked TFBGA88 ball array, 0.8 mm pitch, package mechanical data Symbol ddd E 10.000 FE1 SD SE Millimeters ...
Page 22
... F = RoHS compliant package, tape and reel packing Devices are shipped from the factory with the memory content bits erased to ’1’. For a list of available options (speed, package, etc.) or for further information on any aspect of this device, please contact the Numonyx sales office nearest to you. 22/ ...
Page 23
M36W0Rx0x0x7 8 Revision history Table 9. Document revision history Date Version 30-Jun-2008 29-Sep-2008 31-Mar-2009 Revision Details 1 Initial release. 2 Change from T=-30°C to T=-40°C. Replaced references to ECOPACK with RoHS compliant. 3 Changed footnote 1 in figure1. Revision history ...
Page 24
... NUMONYX PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Numonyx products are not intended for use in medical, life saving, life sustaining, critical control or safety systems nuclear facility Numonyx may make changes to specifications and product descriptions at any time, without notice. ...