EMIF06-MSD02N16 STMicroelectronics, EMIF06-MSD02N16 Datasheet
EMIF06-MSD02N16
Specifications of EMIF06-MSD02N16
Available stocks
Related parts for EMIF06-MSD02N16
EMIF06-MSD02N16 Summary of contents
Page 1
... Navigation systems ■ Digital still cameras ■ Portable devices. Description The EMIF06-MSD02N16 is a highly integrated device designed to suppress EMI/RFI noise for interface line filtering packaged in micro QFN. This filter includes ESD protection circuitry, which prevents damage to the protected device when subjected to ESD surges. ...
Page 2
... Series resistors - tolerance ±20 Pull-up resistors R13 Pull-down resistor - tolerance ±20% V LINE C line (under zero light conditions) 2/12 Parameter = 25 °C) amb RM Test conditions = mV MHz OSC EMIF06-MSD02N16 Value 125 - 150 Min. Typ. Max 200 100 375 470 565 20 Unit kV °C °C °C ...
Page 3
... EMIF06-MSD02N16 Figure 3. S21 attenuation measurement dB 0.00 -10.00 -20.00 -30.00 -40.00 F (Hz) -50.00 100.0k 1.0M 10.0M DAT0 DAT2 CLK Figure 5. ESD response to IEC 61000-4-2 (+12 kV air discharge) on one input (V ) and on one output ( Max Max OUT Figure 7. Line capacitance versus reverse voltage applied on DATx and CMD line ...
Page 4
... DATx and the CMD line must be pulled-up with resistors 100 kΩ to avoid bus floating not only in SD 4-bit mode but also in SD 1-bit and SPI mode. For the EMIF06-MSD02N16 device the pull-up resistor value has been fixed at 90 kΩ. This value makes the EMIF06-MSD02N16 compatible with most of the level shifters that may be used in the circuit including auto direction-sensing translators known to exhibit a weak current output ...
Page 5
... EMIF06-MSD02N16 Figure 8. Mechanical card detection A pull- kΩ is embedded into the EMIF06-MSD02N16. The routing corresponding to the mechanical card detection configuration is shown in Figure 9. Circuit routing for mechanical card detection Card detect pin Pin 2–CD/DAT3 In case of electrical card detection, the user must add a pull-down on the circuit connected to the CD/DAT3 pin of the micro-SD/T-Flash pin as shown in Figure 10 ...
Page 6
... Ordering information scheme A pull-down of 470k is embedded into the EMIF06-mSD02N16. The routing corresponding to the electrical card detection configuration is shown in the Figure 11. Circuit routing for electrical card detection 3 Ordering information scheme Figure 12. Ordering information scheme EMI Filter Number of lines Information MSD = application 02 = version ...
Page 7
... EMIF06-MSD02N16 4 Package information ● Epoxy meets UL94 order to meet environmental requirements, ST offers these devices in ECOPACK packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label ...
Page 8
... PCB. Only pin 1 mark used for this purpose. 8/12 Dot identifying Pin A1 location 4.00 ± 0.1 2.00 ± 0 1.70 ± 0.1 0.80 ± 0.1 User direction of unreeling EMIF06-MSD02N16 Ø 1.55 ± 0. 4.00 ± 0.1 ...
Page 9
... EMIF06-MSD02N16 5 Recommendation on PCB assembly 5.1 Stencil opening design 1. General recommendation on stencil opening design a) Stencil opening dimensions: L (Length), W (Width), T (Thickness). Figure 16. Stencil opening dimensions b) General design rule Stencil thickness ( 125 µm Aspect Ratio Aspect Area 2. Reference design a) Stencil opening thickness: 100 µm b) Stencil opening for central exposed pad: Opening to footprint ratio is 50% ...
Page 10
... To control the solder paste amount, the closed via is recommended instead of open vias. 2. The position of tracks and open vias in the solder area should be well balanced. The symmetrical layout is recommended, in case any tilt phenomena caused by asymmetrical solder paste amount due to the solder flow away. 10/12 EMIF06-MSD02N16 ...
Page 11
... EMIF06-MSD02N16 5.5 Reflow profile Figure 18. ST ECOPACK® recommended soldering reflow profile for PCB mounting Temperature (°C) Temperature (°C) 260°C max 260°C max 255°C 255°C 220°C 220°C 180°C 180°C 125 °C 125 °C ...
Page 12
... Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America 12/12 Please Read Carefully: © 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies www.st.com EMIF06-MSD02N16 ...