T2525N238-DDW Atmel, T2525N238-DDW Datasheet
T2525N238-DDW
Specifications of T2525N238-DDW
Related parts for T2525N238-DDW
T2525N238-DDW Summary of contents
Page 1
Features • No External Components Except PIN Diode • Supply-voltage Range: 4.5V to 5.5V • Highest Sensitivity Due to Automatic Sensitivity Adaption (AGC) and Automatic Strong Signal Adaption (ATC) • Highest Immunity Against Disturbances from Daylight and Lamps • Available ...
Page 2
Figure 1-1. Block Diagram IN Carrier frequency f 0 Modulated IR signal min pulses T2525 2 VS CGA and Input filter AGC/ATC Oscillator and digital control GND OUT Micro- Demodulator controller T2525 4657H–AUTO–05/10 ...
Page 3
Pin Description Table 2-1. Pin Description Symbol Function VS Supply voltage OUT Data output IN Input PIN diode GND Ground 3. Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. ...
Page 4
Electrical Characteristics T = 25° unless otherwise specified. amb S No. Parameters 1 Supply 1.1 Supply-voltage range 1.2 Supply current 2 Output (1) 2.1 Internal pull-up resistor 2.2 Output voltage low 2.3 Output voltage high 2.4 ...
Page 5
Electrical Characteristics (Continued 25° unless otherwise specified. amb S No. Parameters Maximum detection 3.5 threshold current with V IN > Controlled Amplifier and Filter Maximum value of 4.1 variable gain (CGA) Minimum ...
Page 6
Typical Electrical Curves at T Figure 5-1. Figure 5-2. Figure 5-3. T2525 6 = 25°C amb I versus Eemin IN_DC S 100 10 1 0.52 0 0.1 1.0 10.0 I IN_DC V versus I ...
Page 7
Figure 5- Figure 5-5. Illustration of Used Terms 1066 µs 533 µ OUT DON Envelope 1 OUT Data word 17 ms Example kHz, burst with 16 pulses, 16 periods 4657H–AUTO–05/10 ...
Page 8
Figure 5-6. Test Circuit PULSE f I IN_AC100 Figure 5-7. Application Circuit 220 4.7 µF IN_DC Ee 1 T2525 8 I ...
Page 9
Chip Dimensions Figure 6-1. Note: Dimensions Pad metallurgy Finish Note: 4657H–AUTO–05/10 Chip Size in µm GND 351,904 VS 63,660 T2525 63,70 OUT 0,0 Pad coordinates are for lower left corner of the pad in µm from the origin 0,0 ...
Page 10
Ordering Information Delivering: unsawn wafers (DDW) in box. (2) Extended Type Number PL (1) T2525S0xx C-DDW 2 (1) T2525S1xx C-DDW 1 (1) T2525S2xx C-DDW 2 (1) T2525S3xx C-DDW 1 (1) T2525S6xx C-DDW 2 (1) T2525S7xx C-DDW 1 Notes: 1. ...
Page 11
Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. 4657H-AUTO-05/10 4657G-AUTO-09/09 4657F-AUTO-10/06 4657E-AUTO-04/06 4657H–AUTO–05/10 History • Features on page 1 changed • ...
Page 12
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...