HFCT5903E Avago Technologies US Inc., HFCT5903E Datasheet
HFCT5903E
Specifications of HFCT5903E
Available stocks
Related parts for HFCT5903E
HFCT5903E Summary of contents
Page 1
HFCT-5903E MT-RJ Duplex Single Mode Transceiver Data Sheet Description The HFCT-5903E transceiver is a high performance, cost effective module for serial optical data communications applications specified for a signal rate of 125 MBd designed to provide an FDDI ...
Page 2
Connection Diagram RX Package Top Grounding Tabs View RECEIVER SIGNAL GROUND 1 RECEIVER POWER SUPPLY 2 SIGNAL DETECT 3 RECEIVER DATA OUT BAR 4 5 RECEIVER DATA OUT Pin Descriptions: 1 Pin 1 Receiver Signal Ground V RX: EE Directly ...
Page 3
Functional Description Receiver Section Design The receiver section contains an InGaAs/InP photo detector and a preamplifier mounted in an optical subassembly. This optical subassembly is coupled to a postamp/decision circuit on a separate circuit board. The postamplifier is ac coupled ...
Page 4
Functional Description Transmitter Section Design The transmitter section uses a buried heterostruc- ture Fabry Perot laser as its optical source. The package of this laser is designed to allow repeatable coupling into single mode fiber. In addition, this package has ...
Page 5
Interface and Termination Recommendations Figure 3 shows a +3.3 V coupling scheme. Also present are power supply filtering arrangements which comply with the recommendations of the small form factor multisource agreement. Such a compliance ensures noise rejection compatibility between transceivers ...
Page 6
Regulatory Compliance Feature Test Method Electrostatic Discharge MIL-STD-883C (ESD) to the Electrical Pins Method 3015.4 Electrostatic Discharge Variation of IEC 801-2 (ESD) to the Duplex MT-RJ Receptacle Electromagnetic FCC Class B Interference (EMI) CENELEC EN55022 Class B (CISPR 22A) VCCI ...
Page 7
Performance Specifications Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause catastrophic damage to the device. Limits apply to each parameter in isolation, all other parameters having values within the recommended operating conditions. It should not ...
Page 8
Receiver Section (Ambient Operating Temperature V Parameter Supply Current Power Dissipation Receiver Sensitivity at Eye Center Receiver Sensitivity at Window Edge Maximum Input Optical Power Operating Wavelength Data Output Voltage - Low Data Output Voltage - High Signal Detect Output ...
Page 9
OVERALL RECEPTACLE CENTER LINE) 13.59 10.0 (0.535) (0.394) MAX. MAX. (0.18) 7.59 (0.299) 12.4 (0.488) 9.3 9.8 (0.366) (0.386) MAX. MAX. Ø 1.07 (0.042) DIMENSIONS IN MILLIMETERS (INCHES) NOTES: 1. THIS PAGE DESCRIBES THE MAXIMUM PACKAGE ...
Page 10
OVERALL RECEPTACLE CENTER LINE) 13.59 9.6 (0.535) (0.378) MAX. MAX. (0.18) 7.59 (0.299) 12 (0.472) 9.3 9.8 (0.366) (0.386) MAX. MAX. Ø 1.07 (0.042) DIMENSIONS IN MILLIMETERS (INCHES) NOTES: 1. THIS PAGE DESCRIBES THE MAXIMUM PACKAGE ...
Page 11
Board Layout - Decoupling Circuit and Ground Planes It is important to take care in the layout of your circuit board to achieve optimum performance from these transceivers. Figure 3 provides a good example of a schematic for a power ...
Page 12
OF PCB TO MIN. BOTTOM OF OPENING) DIMENSIONS IN MILLIMETERS (INCHES) NOTE: NOSE SHIELD SHOULD BE CONNECTED TO CHASSIS GROUND. Figure 7. Recommended Panel Mounting Ordering Information ...