ISP1760BE,557 NXP Semiconductors, ISP1760BE,557 Datasheet - Page 24
ISP1760BE,557
Manufacturer Part Number
ISP1760BE,557
Description
Manufacturer
NXP Semiconductors
Datasheet
1.ISP1760BE557.pdf
(111 pages)
Specifications of ISP1760BE,557
Package Type
LQFP
Pin Count
128
Lead Free Status / RoHS Status
Compliant
- Current page: 24 of 111
- Download datasheet (570Kb)
NXP Semiconductors
ISP1760_4
Product data sheet
7.5 Phase-Locked Loop (PLL) clock multiplier
7.6 Power management
Table 5.
The internal PLL requires a 12 MHz input, which can be a 12 MHz crystal or a 12 MHz
clock already existing in the system with a precision better than 50 ppm. This allows the
use of a low-cost 12 MHz crystal that also minimizes ElectroMagnetic Interference (EMI).
When an external crystal is used, make sure the CLKIN pin is connected to V
The PLL block generates all the main internal clocks required for normal functionality of
various blocks: 30 MHz, 48 MHz and 60 MHz.
No external components are required for the PLL operation.
The ISP1760 implements a flexible power management scheme, allowing various power
saving stages.
The usual powering scheme implies programming EHCI registers and the internal
Hi-Speed USB (USB 2.0) hub in the same way it is done in the case of a PCI Hi-Speed
USB host controller with a Hi-Speed USB hub attached.
When the ISP1760 is in suspend mode, the main internal clocks will be stopped to ensure
minimum power consumption. An internal LazyClock of 100 kHz
running. This allows initiating a resume on one of these events:
The SUSPEND/WAKEUP_N pin is a bidirectional pin. This pin must be connected to one
of the GPIO pins of a processor.
The awake state can be verified by reading the LOW level of this pin. If the level is HIGH,
it means that the ISP1760 is in the suspend state.
The SUSPEND/WAKEUP_N pin requires a pull-up because in the ISP1760 suspended
state the pin becomes 3-state and can be pulled down, driving it externally by switching
the processor’s GPIO line to output mode to generate the ISP1760 wake-up.
PTD
1
2
3
4
5
6
7
8
9
•
•
•
External USB device connect or disconnect
CS_N signal asserted when the ISP1760 is accessed
Driving the SUSPEND/WAKEUP_N pin to a LOW level
AND register
1
1
0
1
0
0
0
0
0
Using the IRQ Mask AND or IRQ Mask OR registers
Rev. 04 — 4 February 2008
OR register
0
0
0
0
0
0
1
1
1
Time
1 ms
-
-
3 ms
-
-
5 ms
6 ms
7 ms
Embedded Hi-Speed USB host controller
PTD done
1
1
-
1
-
-
1
1
1
IRQ
-
-
-
active because of AND
-
-
active because of OR
active because of OR
active because of OR
40 % will continue
© NXP B.V. 2008. All rights reserved.
ISP1760
CC(I/O)
23 of 110
.
Related parts for ISP1760BE,557
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Hi-speed Universal Serial Bus Host Controller For Embedded Applications
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors