MC13892JVLR2 Freescale, MC13892JVLR2 Datasheet - Page 62
MC13892JVLR2
Manufacturer Part Number
MC13892JVLR2
Description
Manufacturer
Freescale
Datasheet
1.MC13892JVLR2.pdf
(161 pages)
Specifications of MC13892JVLR2
Operating Temperature (max)
85C
Operating Temperature (min)
-30C
Mounting
Surface Mount
Package Type
BGA
Case Length
12mm
Screening Level
Commercial
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MC13892JVLR2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
- Current page: 62 of 161
- Download datasheet (7Mb)
FUNCTIONAL DEVICE OPERATION
OPERATING MODES
TIMING DIAGRAMS
POWER UP
initial delay of 8.0 ms, in which the core circuitry gets enabled. To ensure a proper power up sequence, the outputs of the
switchers are discharged at the beginning of a Cold Start. For that reason, an 8.0 ms delay allows the outputs of the linear
regulators to be fully discharged as well through the built-in discharge path. Time slots which include multiple regulator startups
will be sub-sequenced for additional inrush balancing. The peak inrush current per event is limited. Any under-voltage detection
at BP is masked while the power up sequencer is running.
enabling and output level options are selected by hardwiring the PUMSx pins for the desired configuration. The state of the
PUMSx pins can be read out via the sense bits PUMSSxx[1:0]. Tying the PUMSx pins to ground corresponds to 00, open to 01,
VCOREDIG to 10, and VCORE to 11.
sequestering just the bare essentials, to allow processor startup and software to run. With such a strategy, the startup transients
are controlled at lower levels, and the rest of the system power tree can be brought up by software. This allows optimization of
supply ordering where specific sequences may be required, as well as supply default values. Software code can load up all of
the required programmable options to avoid sneak paths, under/over-voltage issues, startup surges, etc., without any change in
hardware. For this reason, the Power Gate drivers are limited to activation by software rather than the sequencer, allowing the
core(s) to startup before any peripheral loading is introduced.
get enabled.
62
13892
A Turn On event timing diagram example shows in
At power up, switchers and regulators are sequentially enabled in time slots of 2.0 ms steps to limit the inrush current after an
The Power Up mode Select pins (PUMS1 and 2) are used to configure the startup characteristics of the regulators. Supply
The recommended power up strategy for end products is to bring up as little of the system as possible at booting, essentially
The power up defaults
Table 26
Table 25. Timer Main Characteristics
Under-voltage Timer
Reset Timer
Watchdog Timer
Power Cut Timer
shows the initial setup for the voltage level of the switchers and regulators, and whether they
Timer
Figure 12. Power Up Timing Diagram
Figure
4.0 ms
40 ms
128 ms
Programmable 0 to 8 seconds in 31.25 ms steps
12.
Duration
Analog Integrated Circuit Device Data
Freescale Semiconductor
Related parts for MC13892JVLR2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
TOWER ELEVATOR BOARDS HARDWARE
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
TOWER SERIAL I/O HARDWARE
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
LCD MODULE FOR TWR SYSTEM
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
DAUGHTER LCD WVGA I.MX51
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
TOWER SYSTEM BOARD MPC5125
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
KIT EVALUATION I.MX51
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
KIT DEVELOPMENT WINCE IMX25
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
TOWER SYSTEM KIT MPC5125
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
TOWER SYSTEM BOARD K40X256
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
TOWER SYSTEM KIT K40X256
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
Microcontrollers (MCU) MX28 PLATFORM DEV KIT
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
MCU, MPU & DSP Development Tools IAR KickStart Kit for Kinetis K60
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
24BIT HDMI MX535/08
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
Manufacturer:
Freescale Semiconductor, Inc
Datasheet: