BTM7710GXT Infineon Technologies, BTM7710GXT Datasheet
![no-image](/images/manufacturer_photos/0/3/327/infineon_technologies_sml.jpg)
BTM7710GXT
Specifications of BTM7710GXT
Related parts for BTM7710GXT
BTM7710GXT Summary of contents
Page 1
...
Page 2
Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 3
... The BTM7710G is part of the TrilithIC family containing three dies in one package: One double high-side switch and two low-side switches. The drains of these three vertical DMOS chips are mounted on separated lead frames. The sources are connected to individual pins, so the BTM7710G can be used in H-bridge- as well as in any other configuration ...
Page 4
Pin Configuration 2.1 Pin Assignment DL1 1 IL1 2 DL1 3 N.C. 4 DHVS 5 GND 6 IH1 IH2 9 DHVS 10 N.C. 11 DL2 12 IL2 13 DL2 14 Figure 1 Pin Assignment BTM7710G (Top ...
Page 5
... DL1 Drain of low-side switch1, leadframe 1 2 IL1 Analog input of low-side switch1 4 N.C. not connected 5, 10, 19, 24 DHVS Drain of high-side switches and power supply voltage, leadframe 2 6 GND Ground 7 IH1 Digital input of high-side switch1 8 ST Status of high-side switches; open Drain output 9 ...
Page 6
Terms IH1 IH1 V STL V STZ I IH1 IH2 V IH1 GND V IH2 I GND I LKCL I IL1 IL1 I V IL2 IL2 IL1 ...
Page 7
Block Diagram IH1 9 IH2 6 GND 2 IL1 13 IL2 Figure 3 Block Diagram BTM7710G Data Sheet DHVS 5,10,19,24 Diagnosis Biasing and Protection Driver IN OUT ...
Page 8
... Output Stages The output stages consist of an low diodes can be used for freewheeling when communicating inductive loads. If the high-side switches are used as single switches, positive and negative voltage spikes which occur when driving inductive loads are limited by integrated power clamp diodes. ...
Page 9
... Table 3 Truth table and Diagnosis (valid only for the High-Side-Switches) Flag Normal operation; identical with functional truth table Overtemperature high-side switch1 Overtemperature high-side switch2 Overtemperature both high-side switches Under voltage Inputs Logic LOW 1 = Logic HIGH X = don’t care Data Sheet IH1 ...
Page 10
... Electrical Characteristics 5.1 Absolute Maximum Ratings 1) Absolute Maximum Ratings – 40 °C < T < 150 °C j Pos. Parameter High-Side-Switches (Pins DHVS, IH1,2 and SH1,2) 5.1.1 Supply voltage 5.1.2 Supply voltage for full short circuit protection 2) 5.1.3 HS-drain current 5.1.4 HS-input current 5.1.5 HS-input voltage Status Output ST 5 ...
Page 11
Functional Range Pos. Parameter 5.2.20 Supply voltage 5.2.21 Input voltage HS 5.2.22 Input voltage LS 5.2.23 Status output current 5.2.24 Junction temperature Note: Within the functional range the IC operates as described in the circuit description. The electrical characteristics ...
Page 12
... Switch-ON voltage 5.4.36 Switch-OFF voltage 5.4.37 Switch ON/OFF hysteresis Output stages 5.4.38 Inverse diode of high-side switch; Forward-voltage 5.4.39 Inverse diode of low-side switch; Forward-voltage 5.4.40 Static drain-source on-resistance of high-side switch 5.4.41 Static drain-source on-resistance of low-side switch Data Sheet < 150 ° < V < ...
Page 13
... A; – 40 °C < SH1 SH2 SL1 SL2 unless otherwise specified Pos. Parameter Short Circuit of high-side switch to GND 5.4.42 Initial peak SC current 100 µ del S Short Circuit of high-side switch to 5.4.43 Output pull-down-resistor 1) Thermal Shutdown 5.4.44 Thermal shutdown junction temperature 5.4.45 Thermal switch-on junction temperature 5 ...
Page 14
... A; – 40 °C < SH1 SH2 SL1 SL2 unless otherwise specified Pos. Parameter Control Inputs of high-side switches 5.4.62 H-input voltage 5.4.63 L-input voltage 5.4.64 Input voltage hysteresis 5.4.65 H-input current 5.4.66 L-input current 5.4.67 Input series resistance 5.4.68 Zener limit voltage Control Inputs IL1 ...
Page 15
Application Information Note: The following simplified application examples are given as a hint for the implementation of the device only and shall not be regarded as a description or warranty of a certain functionality, condition or quality of the ...
Page 16
Package Outlines 1.27 +0.15 2) 0.35 0.2 28x 28 1 18.1 Index Marking 1) Does not include plastic or metal protrusions of 0.15 max rer side 2) Does not include dambar protrusion of 0.05 max per side Figure 5 ...
Page 17
Revision History Rev. Date Changes 1.0 2008-06-27 Initial version Data Sheet 17 BTM7710G Rev. 1.0, 2008-06-27 ...
Page 18
... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...