5962-89841063A E2V, 5962-89841063A Datasheet - Page 16

• Manufacturer Part Number: 5962-89841063A
• Manufacturer: E2V

Specifications of 5962-89841063A

• Lead Free Status / RoHS Status: Supplier Unconfirmed

DEFENSE SUPPLY CENTER COLUMBUS
DSCC FORM 2234
APR 97
characteristics are as specified in table I and shall apply over the full case operating temperature range.
electrical tests for each subgroup are described in table I.
PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the
entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the
"5962-" on the device.
compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML"
certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used.
an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA
prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of
MIL-PRF-38535, appendix A and the requirements herein.
provided with each lot of microcircuits delivered to this drawing.
appendix A.
manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore
at the option of the reviewer.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all
devices prior to quality conformance inspection. The following additional criteria shall apply:
tests prior to burn-in are optional at the discretion of the manufacturer.
COLUMBUS, OHIO 43218-3990
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be
3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535,
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the
a. Burn-in test, method 1015 of MIL-STD-883.
b. Interim and final electrical parameters shall be as specified in table II herein, except interim electrical parameter
MICROCIRCUIT DRAWING
(1)
(2)
(3)
(4)
Test condition D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent
specified in method 1015 of MIL-STD-883.
T
Devices shall be burned-in containing a pattern that assures all inputs and I/O's are dynamically switched.
This pattern must have all cells programmed in a high or low state (not neutralized).
The burn-in pattern shall be read before and after burn-in. Devices having any logic array bits not in the
proper state shall constitute a device failure and shall be added as failures for PDA calculation.
A
= +125°C, minimum.
STANDARD
SIZE
A
REVISION LEVEL
L
SHEET
5962-89841
16