CYIS1SM1000AA-HHC Cypress Semiconductor Corp, CYIS1SM1000AA-HHC Datasheet - Page 13

• Manufacturer Part Number: CYIS1SM1000AA-HHC
• Description: Image Sensor Monochrome CMOS 1024x1024Pixels 84-Pin JLCC
• Manufacturer: Cypress Semiconductor Corp
• Type: CMOSr

Specifications of CYIS1SM1000AA-HHC

• Sensor Image Color Type: Monochrome
• Sensor Image Size Range: >= 480,000Pixels
• Sensor Image Size: 1024x1024Pixels
• Operating Supply Voltage (typ): 5V
• Operating Temp Range: 0C to 60C
• Package Type: JLCC
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 84
• Package: 84JLCC
• Image Size: 1024x1024 Pixels
• Color Sensing: Monochrome
• Operating Temperature: 0 to 60 °C
• Operating Supply Voltage: 5 V
• Lead Free Status / RoHS Status: Not Compliant

Table 8. Pin List of the STAR1000 Sensor (continued)
Document Number: 38-05714 Rev. *D
Pin
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
9
NBIAS_OAMP
NBIAS_DEC
RESET_DS
BLACKREF
Pin Name
A_SEL1
A_SEL0
RESET
CLK_X
GNDD
GNDA
VDDD
PBIAS
VDDD
VDDA
A_IN2
A_IN3
A_IN1
VDDA
LD_X
OUT
CAL
G1
G0
S
R
Pin Type
Ground
Ground
Supply
Supply
Output
Supply
Supply
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Digital input. Latch address (A0…A9) to X-register (0 = track, 1 = hold).
Analog power supply of the imager (typical 5V).
Digital ground of the imager.
Analog ground of the imager.
Digital input. Clock X-register (output valid & stable when CLK_X is high).
Digital input (active high). Resets row indicated by Y-address (see sensor
timing diagram).
RESET_DS is used for dual-slope integration (see FAQ).
GND is used for normal operation.
Digital supply of the image sensor.
Digital input (active high). Resets row indicated by Y-address (see sensor
timing diagram).
Digital input (active high). Control signal for column amplifier (see sensor
timing diagram).
Digital input (active high). Control signal for column amplifier (see sensor
timing diagram).
Analog input. Biasing of address decoder.
Connect with 100 kΩ to VDDA and decouple with 100nF to GND.
Additional analog inputs. For proper conversion with on-chip ADC, the
input signal must lie within the output signal range of the image sensor
(approximately +2V to +4V).
Selection of analog channel: '00' selects image sensor ('01' selects A_IN1,
'10' A_IN2, and '11' A_IN3).
Analog input. Bias of output amplifier (speed/power control).
Connect with 100 kΩ to VDDA and decouple with 100 nF to GND for 12.5
MHz output rate (lower resistor values yield higher maximal pixel rates at
the cost of extra power dissipation).
Analog input. Biasing of the multiplexer circuitry.
Connect with 20 kΩ to GND and decouple with 100 nF to VDD.
Digital input. Select output amplifier gain value: G0 = LSB, G1 = MSB ('00'
= unity gain, '01' = x2, '10' = x4, '11' = x8).
Digital input (active high). Initialization of output amplifier. Output amplifier
outputs BLACKREF in unity gain mode when CAL is high (1).
Apply pulse pattern (see sensor timing diagram).
Analog Output Video Signal. Connected to the analog input of the internal
(pin 52) 10-bit ADC or an external ADC.
Analog input. Control voltage for output signal offset level. Buffered
on-chip, the reference level can be generated by a 100 kΩ resistive divider.
Connect to 2V DC for use with on-chip ADC.
Analog power supply of image core (typical 5V).
Digital power supply of image core (typical 5V).
Pin Description
STAR1000
Page 13 of 20
[+] Feedback