DS90CR483AVJD National Semiconductor, DS90CR483AVJD Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
DS90CR483AVJD
Manufacturer Part Number
DS90CR483AVJD
Description
Manufacturer
National Semiconductor
Datasheet
1.DS90CR483AVJD.pdf
(24 pages)
Specifications of DS90CR483AVJD
Number Of Elements
8
Input Type
CMOS/TTL
Operating Supply Voltage (typ)
3.3V
Output Type
Serializer
Power Dissipation
2.3W
Operating Temp Range
-10C to 70C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
100
Number Of Receivers
48
Number Of Drivers
8
Lead Free Status / RoHS Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS90CR483AVJD/NOPB
Manufacturer:
NSC
Quantity:
106
Company:
Part Number:
DS90CR483AVJD/NOPB
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
DS90CR483AVJDX/NOPB
Manufacturer:
Texas Instruments
Quantity:
10 000
www.national.com
TxIN
TxOUTP
TxOUTM
TxCLKIN
TxCLKP
TxCLKM
PD
PLLSEL
PRE
DS_OPT
BAL
V
GND
PLLV
PLLGND
LVDSV
LVDSGND
NC
CC
DS90CR483A Pin Descriptions—Channel Link Transmitter
Note 11: Inputs default to “low” when left open due to internal pull-down resistor.
CC
Pin Name
CC
I/O
O
O
O
O
I
I
I
I
I
I
I
I
I
I
I
I
I
TTL level input. (Note 11).
Positive LVDS differential data output.
Negative LVDS differential data output.
TTL level clock input. The rising edge acts as data strobe.
Positive LVDS differential clock output.
Negative LVDS differential clock output.
TTL level input. Assertion (low input) tri-states the outputs, ensuring low current at power down.
(Note 11).
PLL range select. This pin should be tied to V
the PLL to low range. Low range is 33 — 40 MHz. High range is 38 — 112 MHz.(Note 11)
Pre-emphasis “level” select. Pre-emphasis is active when input is tied to V
pull-up resistor. Resistor value determines Pre-emphasis level (See Applications Information
Section). For normal LVDS drive level (No Pre-emphasis) leave this pin open (do not tie to
ground).
Cable Deskew performed when TTL level input is low. No TxIN data is sampled during Deskew.
To perform Deskew function, input must be held low for a minimum of 4 clock cycles. The Deskew
operation is normally conducted after the TX and RX PLLs have locked. It should also be
conducted after a system reset, or a reconfiguration event. It must be performed at least once
when "DESKEW" is enabled. (Note 11) Deskew is only supported in the DC Balance mode (BAL
= High).
TTL level input. This pin was previously labeled as V
But when tied low or left open, the DC Balance function is disabled. Please refer to (Figures
15, 16) for LVDS data bit mapping respectively. (Note 11), (Note 13)
Power supply pins for TTL inputs and digital circuitry. Bypass not required on Pins 20 and 21.
Ground pins for TTL inputs and digital circuitry.
Power supply pin for PLL circuitry.
Ground pins for PLL circuitry.
Power supply pin for LVDS outputs.
Ground pins for LVDS outputs.
No Connect. Make NO Connection to these pins - leave open.
18
Description
CC
for high-range. Tied to ground or NC will force
CC
, which enabled the DC Balance function.
CC
through external