TFBS5711-TR1 Vishay, TFBS5711-TR1 Datasheet - Page 5

• Manufacturer Part Number: TFBS5711-TR1
• Manufacturer: Vishay
• Type: TX/RXr

Specifications of TFBS5711-TR1

• Peak Wavelength: 900nm
• Angle Of Half Sensitivity: 48°
• Pulse Width: 2us
• Led Supply Voltage: -0.5 to 6.5V
• Package Type: SMD
• Fall Time: 40/60ns
• Rise Time: 40/60ns
• Dimensions: 6x3.1x1.9
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 5.5V
• Mounting: Surface Mount
• Pin Count: 6
• Operating Temp Range: -25C to 85C
• Operating Temperature Classification: Commercial
• Data Rate: 1.125Mbps
• Lead Free Status / RoHS Status: Compliant

TFBS5711
Vishay Semiconductors
*)
TFDU5307 is set to the "short output pulse" as default after power on, also after recovering from the shutdown mode (SD must have been
longer active than 1.5 ms). For mode changing see the chapter "Programming"
Transmitter
T
Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
*)
the standard Remote Control applications with codes as e.g. Phillips RC5/RC6
operating range of about 4 m can be expected.
www.vishay.com
234
Stochastic jitter, leading edge
Standby /Shutdown delay
Shutdown active time window for
programming
Receiver start up time power on
delay shutdown recovery delay
Latency
IRED operating current,
recommended serial resistor for
MIR applications
Output leakage IRED current
Output radiant intensity
recommended application
circuit, see figure 1
Output radiant intensity
Output radiant intensity, angle of
half intensity
Peak - emission wavelength
Spectral bandwidth
Optical rise time, fall time
Optical output pulse duration
Optical overshoot
amb
Note: Due to this wavelength restriction compared to the IrDA spec of 850 nm to 900 nm the transmitter is able to operate as source for
Some ENDECs are not able to decode short pulses as valid SIR pulses. Therefore this additional mode was added in TFDU5307.
= 25 °C, V
Parameter
Parameter
CC1
= V
CC2
= 2.7 V to 5.5 V unless otherwise noted.
*)
V
V
TXD = 0 V, 0 < V
I
α = 15 °, V
TXD = High, SD = Low
V
TXD = Low or SD = High
(Receiver is inactive as long as
SD = High)
Input pulse width 217 ns,
1.152 Mbit/s
Input pulse width t
Input pulse width t
F
Input irradiance = 100 mW/m
1.152 Mbit/s, 576 kbit/s
Input irradiance = 100 mW/m
≤ 115.2 kbit/s
After shutdown active or (SD low
to high transition)
During this time the pulse
duration of the output can be
programmed to the application
mode. see chapter
"Programming"
After shutdown inactive (SD
high to low transition) and after
power-on
CC2
CC2
CC1
= 250 mA, α = 0 °,
= 3.3 V: R
= 5.0 V: R
= 5.0 V, α = 0 °, 15 °
Test Conditions
Test Conditions
CC2
= 2.7 V,
S
S
CC1
= 2.0 Ω
= 5.6 Ω
TXD
TXD
< 5.5 V
< 80 µs
≥ 80 µs
2
2
,
,
t
Symbol
ropt
Symbol
I
IRED
t
t
t
Δλ
λ
I
opt
opt
opt
I
I
α
, t
D
e
e
p
t
L
fopt
®
or RECS 80. With the typical specified intensity an RC
Min
880
200
- 1
10
10
20
20
Min
0.6
± 24
Typ.
400
217
25
45
Typ.
Document Number 82634
Max
0.04
t
500
900
240
TXD
Max
350
600
300
200
40
85
25
1.5
80
1
Rev. 1.5, 03-Jul-06
mW/sr
mW/sr
Unit
mA
nm
nm
Unit
µA
ns
ns
µs
µs
ms
%
ns
ns
µs
µs
µs
°