CAT5221WI-00TE13 ON Semiconductor, CAT5221WI-00TE13 Datasheet - Page 2
![](/photos/31/40/314081/20pin_soic__sml.jpg)
CAT5221WI-00TE13
Manufacturer Part Number
CAT5221WI-00TE13
Description
Manufacturer
ON Semiconductor
Datasheet
1.CAT5221WI-00TE13.pdf
(16 pages)
Specifications of CAT5221WI-00TE13
Number Of Elements
2
# Of Taps
64
Resistance (max)
100KOhm
Power Supply Requirement
Single
Interface Type
Serial (2-Wire/I2C)
Single Supply Voltage (typ)
3.3/5V
Dual Supply Voltage (typ)
Not RequiredV
Single Supply Voltage (min)
2.5V
Single Supply Voltage (max)
6V
Dual Supply Voltage (min)
Not RequiredV
Dual Supply Voltage (max)
Not RequiredV
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
20
Lead Free Status / RoHS Status
Compliant
Document No. 2113, Rev. I
The CAT5221 is two resistor arrays integrated with 2-
wire serial interface logic, two 6-bit wiper control registers
and eight 6-bit, non-volatile memory data registers.
Each resistor array contains 63 separate resistive
elements connected in series. The physical ends of
each array are equivalent to the fixed terminals of a
mechanical potentiometer (R
symmetrical and may be interchanged. The tap positions
between and at the ends of the series resistors are
connected to the output wiper terminals (R
10
11
12
13
14
15
16
17
18
19
20
1
2
3
4
5
6
7
8
9
GND
SDA
VCC
SCL
R
R
R
R
R
R
NC
NC
NC
NC
NC
NC
A0
A2
A3
A1
W0
W1
L0
H0
L1
H1
Wiper Terminal for Potentiometer 0
Low Reference Terminal for Potentiometer 0
High Reference Terminal for Potentiometer 0
Device Address, LSB
Device Address
Wiper Terminal for Potentiometer 1
Low Reference Terminal for Potentiometer 1
High Reference Terminal for Potentiometer 1
Serial Data Input/Output
Ground
No Connect
No Connect
No Connect
Bus Serial Clock
Device Address
Device Address
No Connect
No Connect
No Connect
Supply Voltage
H
and R
L
). R
H
and R
W
) by a
L
are
2
CMOS transistor switch. Only one tap point for each
potentiometer is connected to its wiper terminal at a time
and is determined by the value of the wiper control
register. Data can be read or written to the wiper control
registers or the non-volatile memory data registers via
the 2-wire bus. Additional instructions allow data to be
transferred between the wiper control registers and
each respective potentiometer's non-volatile data
registers. Also, the device can be instructed to operate
in an "increment/decrement" mode.
The CAT5221 serial clock input pin is used to clock
all data transfers into or out of the device.
The CAT5221 bidirectional serial data pin is used
to transfer data into and out of the device. The
SDA pin is an open drain output and can be wire-
OR'd with the other open drain or open collector
outputs.
These inputs set the device address when
addressing multiple devices. A total of sixteen
devices can be addressed on a single bus.
A match in the slave address must be made
with the address input in order to initiate
communication with the CAT5221.
The two sets of R
to the terminal connections on a mechanical
potentiometer.
The two R
terminal of a mechanical potentiometer.
Resistor End Points
Serial Clock
Serial Data
Wiper
W
pins are equivalent to the wiper
H
Device Address Inputs
and R
L
pins are equivalent