CUB7CVS0 Red Lion Controls, CUB7CVS0 Datasheet - Page 6
![COUNTER 8-DIGIT HV REFLECTIVE](/photos/6/45/64500/cub7cvs0_sml.jpg)
CUB7CVS0
Manufacturer Part Number
CUB7CVS0
Description
COUNTER 8-DIGIT HV REFLECTIVE
Manufacturer
Red Lion Controls
Series
CUB7r
Datasheet
1.CUB7CCS0.pdf
(8 pages)
Specifications of CUB7CVS0
Count Rate
10kHz
Number Of Digits/alpha
8
Input Type
*
Voltage - Supply
None Required (Battery Included)
Display Type
LCD Non-Backlit
Output Type
*
No. Of Digits / Alpha
8
Digit Height
8.9mm
Counting Speed
10kHz
Operating Temperature Range
0°C To +50°C
Display Mode
LCD Positive Reflective
Backlighting Color
Red
Panel Cutout Height
0.874"
Backlight Power
9-28VDC
Counter Supply Voltage
9-28VDC
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
RLC138
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CUB7CVS0
Manufacturer:
Red Lion Controls
Quantity:
135
USING THE OPTIONAL TERMINAL BLOCK
1. Remove the rear cover. Refer to Figure 1. A small slotted screwdriver is
2. For safety concerns, the wires should be cut off completely flush with the PC
3. Break out the break away tab(s) as required. Remove the left tab only for 3
4. Reinstall the rear cover into CUB7 unit.
5. Mount the CUB7 into the panel (refer to 1.0 Installing The Meter)
6. Push the keyed terminal block onto the exposed PC board. The left most
Note: Wire sizes 16-24 AWG may be used with 0.25" length exposed. The
Current Sinking Output
Switch/Contact Sinking Output
required to release the side latches. Insert the screwdriver tip between the
rear cover and the side of the unit. Leverage the screwdriver away from the
case to unlatch the side latch and slightly lift the rear cover. Pinch the
corners to hold the rear cover in place. Remove the screwdriver and repeat
the same procedure on the other side of the rear cover. When both side
latches are released, slide the rear cover from the unit and the wires.
board to prevent a short.
position terminal block or both tabs for 4 and 5 position terminal blocks.
terminal, next to the DIP switch(s) is terminal #1.
screwless type terminal block requires a small slotted screwdriver engaged in
the upper slot to open the wire clamp in the lower larger slot. Removing the
screwdriver will lock the wire clamp unto the wire.
ON
1
ON
1
2
2
*
3
Switch position is application dependent.
*
3
Wires must be cut off completely
flush with PC board.
1
1
2
2
3
3
4
4
+
−
+
−
DIP Switch(s)
Cut Wires Internally
Optional
Backlight
Power
Optional
Backlight
Power
(If using Optional
Terminal Block)
Current Sourcing Output
Switch/Contact Sourcing Output
ON
1
ON
1
2
2
3
*
*
3
Side Latches
+V
+V
Break-out Tab or Tabs
(If using Optional
1
1
Terminal Block)
2
6
2
3
3
4
4
+
−
+
−
Latches
Backlight
Power
Optional
Optional
Backlight
Power
Side
Rear Cover
Shaded area for high voltage applications.
Figure 1
Logic Output
ON
High Voltage
ON
1
3
*
2
*
3
VDC/VAC
50-250
Open & Lock
Mounting Clip
Wire Clamp
1
1
2
2
3
3
4
4
5
Terminal #1
+
−
Optional
Terminal Block
+
−
Optional
Backlight
Power
Optional
Backlight
Power