IMI04160 Red Lion Controls, IMI04160 Datasheet - Page 3

IMI04160

Manufacturer Part Number

IMI04160

Description

PNL METER DIGITAL 115/230VAC

Manufacturer

Red Lion Controls

Series

IMIr

Type

Rate Meterr

Datasheet

1.IMI04160.pdf (4 pages)

Specifications of IMI04160

Measuring Range

0 ~ 50kHz

Display Style

Red Characters, Black Background

Display Type

LED

Display Face Size

3.80" L x 1.95" W (96.5 x 49.5mm)

Display Digits

Display Digits - Height

0.560" (14.22mm)

Backlight

Without

Mounting Type

Panel Mount

Termination

Terminal Block

Voltage - Supply

115/230VAC

Lead Free Status / RoHS Status

Vendor undefined / Vendor undefined

Other names

Q4248729

Current page: 3 of 4
Download datasheet (316Kb)

useful in alarm set-ups where a pre-warning control activates before a second

alarm shuts off the process when tracking is programmed. Changing the shut-

off trip value (Alarm #2) automatically changes Alarm #1 so that the offset

between Alarm #2 and Alarm #1 remains the same.

ISOLATED RE-TRANSMITTED ANALOG

OUTPUT OPTION

4 to 20 mA

4 to 20 mA current to drive chart recorders, remote indicators and controllers.

PROGRAMMABLE FUNCTIONS

a short sequence of data entries. The front panel “UP” and “DOWN” buttons

(shown as “arrows” on the front panel) are used to change the data and set-ups,

while the “P” button is used to save or enter the data. After pressing “P”, the user

gains entry into the programming mode. The programming modules are

identified by the message “Pro” and a module number in the display. “UP” and

“DOWN” are used to select the desired programming module and “P” is used to

enter it. All of the subsequent programming steps follow the same procedure.

The rear terminal labeled “PGM.DIS.” must be inactive (ungrounded) to gain

access to programming. The following table lists the programming steps.

“Pro 0” - RETURN TO MEASUREMENT MODE

“Pro 1” - SCALE UNIT BY APPLYING SIGNAL

“Pro 2” - SCALE UNIT BY KEY-IN SIGNAL LEVEL

“Pro 3” - PROGRAM FUNCTIONS ACCESSIBLE WITH FRONT

“Pro 4” - PROGRAM DIGITAL FILTERING AND REMOTE INPUT

Alarm #1 can be made to track Alarm #2 by enabling alarm tracking. This is

The re-transmitted analog output option transmits a digitally programmable

Programming of the indicator is divided into modular steps. Each module is

“dSPHYS” -

“dSPbUF” -

“SELdSP” -

“E1-CON” -

“ENtHYS” -

“dECPNt” -

PANEL LOCKOUT ENGAGED

(E1-CON & E2-CON) FUNCTION

“dSP AL” -

“SCALE” -

“ENt AL” -

“rStbUF” -

“Lo-udt” -

“dSP 1” -

“rAtE 1” -

“dSP 1” -

“rAtE 1” -

“Hi-udt” -

“rSt AL” -

“round” -

“rSttOt” -

“FILter” -

“SEGt” -

10 -

12 -

11 -

0 -

1 -

2 -

3 -

0 -

1 -

2 -

3 -

4 -

5 -

6 -

7 -

8 -

9 -

Toggle display between input rate and total or effciency

Enter decimal point for scaled input display

Enter rounding factor and trailing zeros for scaled

input display

Enter low update time for rate display updates

Enter high update time for rate display updates

✧

Enter display reading for scaling point #1

Apply rate value for scaling point #1

✧

Enter decimal point for scaled display

Enter rounding factor and trailing zeros for scaled

display

Enter low update time for rate display updates

Enter high update time for rate display updates

✧

Enter display reading for scaling point #1

Enter rate value for scaling point #1

✧

Enable display alarms

Enable enter alarms

Enable display hysteresis

Enable enter hysteresis

Enable reset latched alarms

Enable display of peak/valley readings

Enable reset of peak/valley readings

Enable switching display between input and

total/efficiency

Enable reset total

Enter level of digital filtering

no digital filtering

normal level

increased level

maximum level

Enter function of remote input

Re-start measurement time for input

Reset total

Reset and gate totalizer

Gate totalizer

Display hold

Reset peak/valley

Reset peak and start peak indicator

Reset valley and start valley indicator

Reset latched alarms

Reset all alarms

Input rate functions as a triggered rate meter

Print request

The compliance is 10 VDC. Non-standard current ranges within the 4 to 20 mA

range can be supported by calculating the slope and intercept of the

display/output and calculating the required display values at 4 mA and 20 mA.

0 to 10 VDC

0 to 10 VDC output signal to drive chart recorders, remote indicators and

controllers. Non-standard voltage ranges within the 0 to 10 VDC range can be

supported by calculating the slope and intercept of the display/output and

calculating the required display values at 0 VDC and 10 VDC.

“Pro 5” - PROGRAM SECOND DISPLAY AS TOTALIZER OR

“Pro 6” - PROGRAM ALARMS

“Pro 7” - PROGRAM SERIAL COMMUNICATIONS

“Pro 8” - PROGRAM RE-TRANSMITTED ANALOG OUTPUT

“Pro 9” - FACTORY SERVICE OPERATIONS

✧ - Entire sequence for this modular step is not shown (see manual for further

- This sequence may be locked-out due to other programmed sequences.

The re-transmitted analog output option transmits a digitally programmable

details).

“E2-CON” < >

“ASNbUF” -

“SCLFAC” -

“OndEL1” -

“OFdEL1” -

“OndEL2” -

“OFdEL2” -

EFFICIENCY TOTALIZER

“dECPNt” -

“dELAY1” -

“dELAY2” -

(Protected by access codes)

“AddrES” -

“100Pct” -

“LAtC-1” -

“LAtC-2” -

“ASN-1” -

“HYS-1” -

“ASN-2” -

“HYS-2” -

“tbASE” -

“AN-Lo” -

“Lo-cut” -

“AN-HI” -

“FULL” -

“Act-1” -

“Act-2” -

“bAud” -

“ASIN” -

“dISP” -

“AL-1” -

“AL-2” -

“Print” -

“trAc” -

“0” -

“1” -

“2” -

“3” -

“4” -

“5” -

“6” -

“7” -

“8” -

“9” -

E2-CON has the same programmable functions as

E1-CON.

Select desired display (Total or Efficiency)

Enter decimal point for totalizer

Enter time base

0 - Divide by 1 (second)

1 - Divide by 60 (minute)

2 - Divide by 3600 (hour)

Enter multiplying scale factor

Enter low-signal cut out

Assign peak/valley buffers

Enter decimal point for efficiency

Enter value for desired 100 percent target value

Enable alarm value tracking

Enable display alarm annunciators

Enable alarm #1 latching

Enter alarm #1 trigger source (input or total/eff.)

Enter alarm #1 value

Enter hysteresis value for alarm #1

Enter alarm #1 action (high or low)

Enable delay ON action for alarm #1

Enable delay OFF action for alarm #1

(disabled if delay ON is selected)

Enter delay time value

Enable alarm #2 latching

Enter alarm #2 trigger source (input or total/eff.)

Enter alarm #2 value

Enter hysteresis value for alarm #2

Enter alarm #2 action (high or low)

Enable delay ON action for alarm #2

Enable delay OFF action for alarm #2

(disabled if delay ON is selected)

Enter delay time value

Enter baud rate

Enter loop address number (0-99)

Enter print function

rate

rate, peak, valley

rate, alarm 1, alarm 2

rate, alarm 1, alarm 2, hysteresis 1, hysteresis 2,

peak, valley

totalizer/efficiency

rate, totalizer/efficiency

rate, totalizer/efficiency, peak, valley

totalizer/efficiency, alarm 1, alarm 2

rate, totalizer/efficiency, alarm 1, alarm 2

rate, totalizer/efficiency, alarm 1, alarm 2, hysteresis 1,

hysteresis 2, peak, valley

Enable/Disable abbreviated printing

Select source of analog output (input or total/eff.)

Enter 4 mA or 0 VDC display value

Enter 20 mA or 10 VDC display value

EFFICIENCY

TOTALIZER