3003R-67X-0001 Curtis Instruments Inc, 3003R-67X-0001 Datasheet - Page 2

• Manufacturer Part Number: 3003R-67X-0001
• Description: METER MAINTENANCE 2"RND 12-48VDC
• Manufacturer: Curtis Instruments Inc
• Series: enGage™ II, 3000r
• Type: Programmable Maintenance Monitor with Hour Meterr

Specifications of 3003R-67X-0001

• Shape: Circular
• Voltage Rating: 12 ~ 48V
• Display Type: LCD - 10 Segment Bar, 5 Digits
• Operating Temperature: -40°C ~ 85°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 17631703-67X-0001; 267-1033

Access to these operations is sequential in this order.
Adjustments of the following functions can be
performed in the Configuration Mode:
1. Time-of-Day Clock
2. Maintenance interval
During configuration, the right button is used to
increment. The left button is used to:
1. Enter a selection
2. Advance to the next configurable item
If no change is desired to a specific gauge function,
continue to press the left button until the next desired
function is reached. The time-of-day clock is entered
by setting the hours digits between 01 and 12, then
"minutes" digits between "00" and "59".
The maintenance interval (when the gauge signals that
maintenance is due) is configurable and should be set
after the initial installation. The interval can be set
between 1 and 9,999 hours in 1 hour increments.
Setting the Maintenance Interval
Apply V+ (9 to 60VDC to the set up enable pin (2).
Press and hold the Left button on the front panel until
the display flashes and then release. The display will
flash the two "Hours" digits , Press the left button
once. The display will flash the two "Minutes" digits ,
Press the left button once. The display will flash the
maintenance left digit (thousands of hours). Press the
right button to increment by one or hold the button to
increment continuously. When the desired number is
reached, press the left button once to proceed to the
next digit. Repeat this process for all 4 digits. , Press
the left button once to exit.
This can be done without V+ applied to Setup Enable
pin. Press and hold the left button on the front panel
until the entire display flashes and then release.
The display will flash the two "Hours" digits. Press the
right button to increment by one hour, or hold the
button to increment continuously. When the desired
number of hours is reached, press the left button once.
The display will flash the two "Minutes" digits. Press
the right button to increment by one minute or hold the
button to increment continuously. When the desired
number of minutes is reached, press the left button
once.
Setting the Time-of-Day Clock
Configuring Your Gauge
The gauge remains in configuration mode for 30
seconds without input from the user. When configuring
each function (time-of-day, maintenance interval, etc.),
you must enter in all data for that function for it to be
saved. If incomplete data is entered for a function and
the programming mode is timed out (after 30 seconds
of no input received by the gauge), the gauge will
revert back to what was previously stored for that item.
The configuration mode can be exited in three ways:
1. Press and hold the left button for three seconds.
2. Leave buttons untouched for 30 seconds.
3. Press the left button after selecting the last (right)
digit of the last function available.
When the main power (9-60 VDC) is applied to V+ and
V-, a power-up sequence is initiated. All display
segments are illuminated for one second. The display
is then turned off until the key switch is activated.
Press the left button to sequentially toggle between the
two numeric gauge functions (time-of-day clock,
maintenance hours).
This can be done without V+ applied to Setup Enable
pin. Press the left button until the maintenance hour
meter function is displayed (the wrench icon will be
illuminated). Press and hold both the right button and
the left button until the display flashes and the
maintenance hour meter is reset to the preset
maintenance period. Release the right button first. This
reset function can be performed at any time,
independent of the actual maintenance status.
Resetting the Maintenance Hour
Toggling Display Functions
Exiting Configuration Mode
Configuration Notes
Operation
Meter
1 0
2