PCK2001MDB,112 NXP Semiconductors, PCK2001MDB,112 Datasheet - Page 9
![IC 1:10 CLOCK BUFFER 28SSOP](/photos/6/52/65218/568-28-ssop_sot341-1_sml.jpg)
PCK2001MDB,112
Manufacturer Part Number
PCK2001MDB,112
Description
IC 1:10 CLOCK BUFFER 28SSOP
Manufacturer
NXP Semiconductors
Type
Fanout Buffer (Distribution)r
Datasheet
1.PCK2001MDB118.pdf
(14 pages)
Specifications of PCK2001MDB,112
Package / Case
28-SSOP
Number Of Circuits
1
Ratio - Input:output
1:10
Differential - Input:output
No/No
Input
LVTTL
Output
LVTTL
Frequency - Max
150MHz
Voltage - Supply
3.135 V ~ 3.465 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Frequency-max
150MHz
Number Of Outputs
10
Max Input Freq
133 MHz
Propagation Delay (max)
2.5 ns
Supply Voltage (max)
3.465 V
Supply Voltage (min)
3.135 V
Maximum Power Dissipation
850 mW
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
935262449112
PCK2001MDB
PCK2001MDB
PCK2001MDB
PCK2001MDB
Philips Semiconductors
For example:
A transfer is considered valid after the acknowledge bit corresponding to the byte count is read by the controller. The serial controller interface
can be simplified by discarding the information in both the command code and the byte count bytes and simply reading all the bytes that are
sent to the clock driver after being addressed by the controller. It is expected that the controller will not provide more bytes than the clock driver
can handle. A clock vendor may choose to discard any number of bytes that exceed the defined byte count.
8) Clock stretching: The clock device must not hold/stretch the SCLOCK or SDATA lines low for more than 10 mS. Clock stretching is
discouraged and should only be used as a last resort. Stretching the clock/data lines for longer than this time puts the device in an error/time-out
mode and may not be supported in all platforms. It is assumed that all data transfers can be completed as specified without the use of
clock/data stretching.
9) General Call: It is assumed that the clock driver will not have to respond to the ‘‘general call.”
10) Electrical Characteristics: All electrical characteristics must meet the standard mode specifications found in section 15 of the I
a) Pull-Up Resistors: Any internal resistors pull-ups on the SDATA and SCLOCK inputs must be stated in the individual datasheet. The use of
internal pull-ups on these pins of below 100 k is discouraged. Assume that the board designer will use a single external pull-up resistor for each
line and that these values are in the 5 – 6 k Ohm range. Assume one I
clock driver plus one/two more I
(b) Input Glitch Filters: Only fast mode I
mode device and is not required to support this feature.
11) PWR DWN#: If a clock driver is placed in PWR DWN# mode, the SDATA and SCLK inputs must be 3-Stated and the device must retain all
programming information. I
For specific I
2000 May 17
MSB
0000
0000
0000
0000
0000
0000
0000
0000
0010
Byte count byte
14.318–150 MHz I
0000 Not allowed. Must have at least one byte.
0001 Data for functional and frequency select register (currently byte 0 in spec)
0010 Reads first two bytes of data. (byte 0 then byte 1)
0100 Reads first four bytes (byte 0, 1, 2, 3 in order)
0101 Reads first five bytes (byte 0, 1, 2, 3, 4 in order)
0000 Max byte count supported = 32
0011 Reads first three bytes (byte 0, 1, 2 in order)
0110 Reads first six bytes (byte 0, 1, 2, 3, 4, 5 in order)
0111 Reads first seven bytes (byte 0, 1, 2, 3, 4, 5, 6 in order)
LSB
2
C information consult the Philips I
dd
current due to the I
2
C devices on the platform for capacitive loading purposes.
2
C 1:10 clock buffer
2
C devices require input glitch filters to suppress bus noise. The clock driver is specified as a standard
2
C Peripherals Data Handbook IC12 (1997) .
2
C circuitry must be characterized and in the data sheet.
2
C device per DIMM (serial presence detect), one I
9
Notes:
PCK2001M
2
C controller, one
Product specification
2
C specification.