IDT5T905PGI IDT, Integrated Device Technology Inc, IDT5T905PGI Datasheet - Page 4

• Manufacturer Part Number: IDT5T905PGI
• Description: IC CLK BUFFER 1:5 SGL 28-TSSOP
• Manufacturer: IDT, Integrated Device Technology Inc
• Type: Fanout Buffer (Distribution)r

Specifications of IDT5T905PGI

• Number Of Circuits: 1
• Ratio - Input:output: 1:5
• Differential - Input:output: Yes/No
• Input: eHSTL, HSTL, LVPECL, LVTTL
• Output: eHSTL, HSTL, LVTTL
• Frequency - Max: 250MHz
• Voltage - Supply: 2.4 V ~ 2.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 28-TSSOP
• Frequency-max: 250MHz
• Number Of Outputs: 5
• Operating Supply Voltage (max): 2.6V
• Operating Temp Range: -40C to 85C
• Propagation Delay Time: 3.5ns
• Operating Supply Voltage (min): 2.4V
• Mounting: Surface Mount
• Pin Count: 28
• Operating Supply Voltage (typ): 2.5V
• Package Type: TSSOP
• Quiescent Current: 30mA
• Duty Cycle: 60%
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 5T905PGI

DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
NOTE:
1. These inputs are normally wired to V
INPUT/OUTPUT SELECTION
NOTE:
1. The INPUT/OUTPUT SELECTION Table describes the total possible combinations of input and output interfaces. Single-Ended (SE) inputs in a single-ended mode require the
IDT5T905
2.5V SINGLE DATA RATE 1:5 CLOCK BUFFER TERABUFFER
A/V
differential mode.
Symbol
V
V
V
I
REF
IHH
IMM
ILL
3
pin to be connected to GND. Differential Single-Ended (DSE) is for single-ended operation in differential mode, requiring a V
Input HIGH Voltage Level
Input MID Voltage Level
Input LOW Voltage Level
3-Level Input DC Current (RxS, TxS)
2.5V LVTTL DSE
1.8V LVTTL DSE
2.5V LVTTL DSE
1.8V LVTTL DSE
LVEPECL DSE
LVEPECL DSE
2.5V LVTTL DIF
1.8V LVTTL DIF
2.5V LVTTL DIF
1.8V LVTTL DIF
2.5V LVTTL SE
1.8V LVTTL SE
2.5V LVTTL SE
1.8V LVTTL SE
LVEPECL DIF
LVEPECL DIF
eHSTL DSE
eHSTL DSE
HSTL DSE
eHSTL DIF
HSTL DSE
eHSTL DIF
HSTL DIF
HSTL DIF
Input
Parameter
DD
, GND, or left floating. Internal termination resistors bias unconnected unputs to V
(1)
(1)
(1)
(1)
2.5V LVTTL
1.8V LVTTL
Output
3-Level Inputs Only
3-Level Inputs Only
3-Level Inputs Only
V
V
V
IN
IN
IN
= V
= V
= GND
DD
DD
/2
4
Test Conditions
HIGH Level
MID Level
LOW Level
2.5V LVTTL DSE
1.8V LVTTL DSE
2.5V LVTTL DSE
1.8V LVTTL DSE
LVEPECL DSE
LVEPECL DSE
2.5V LVTTL DIF
1.8V LVTTL DIF
2.5V LVTTL DIF
1.8V LVTTL DIF
2.5V LVTTL SE
1.8V LVTTL SE
2.5V LVTTL SE
1.8V LVTTL SE
LVEPECL DIF
LVEPECL DIF
eHSTL DSE
eHSTL DSE
HSTL DSE
eHSTL DIF
HSTL DSE
eHSTL DIF
HSTL DIF
HSTL DIF
Input
DD
/2.
INDUSTRIAL TEMPERATURE RANGE
REF
V
V
DD
DD
. Differential (DIF) inputs are used only in
Min.
–200
/2 – 0.2
–50
—
—
– 0.4
V
DD
Max
/2 + 0.2
+50
200
0.4
—
—
Output
eHSTL
HSTL
Unit
μA
V
V
V