IDT5T905PGI IDT, Integrated Device Technology Inc, IDT5T905PGI Datasheet - Page 9

• Manufacturer Part Number: IDT5T905PGI
• Description: IC CLK BUFFER 1:5 SGL 28-TSSOP
• Manufacturer: IDT, Integrated Device Technology Inc
• Type: Fanout Buffer (Distribution)r

Specifications of IDT5T905PGI

• Number Of Circuits: 1
• Ratio - Input:output: 1:5
• Differential - Input:output: Yes/No
• Input: eHSTL, HSTL, LVPECL, LVTTL
• Output: eHSTL, HSTL, LVTTL
• Frequency - Max: 250MHz
• Voltage - Supply: 2.4 V ~ 2.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 28-TSSOP
• Frequency-max: 250MHz
• Number Of Outputs: 5
• Operating Supply Voltage (max): 2.6V
• Operating Temp Range: -40C to 85C
• Propagation Delay Time: 3.5ns
• Operating Supply Voltage (min): 2.4V
• Mounting: Surface Mount
• Pin Count: 28
• Operating Supply Voltage (typ): 2.5V
• Package Type: TSSOP
• Quiescent Current: 30mA
• Duty Cycle: 60%
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 5T905PGI

POWER SUPPLY CHARACTERISTICS FOR 2.5V LVTTL OUTPUTS
NOTES:
1. These power consumption characteristics are for all the valid input interfaces and cover the worst case input and output interface combinations.
2. The termination resistors are excluded from these measurements.
3. If the differential input interface is used, the true input is held LOW and the complementary input is held HIGH.
SINGLE-ENDED INPUT AC TEST CONDITIONS FOR 2.5V LVTTL
NOTES:
1. A nominal 1.25V timing measurement reference level is specified to allow constant, repeatable results in an automatic test equipment (ATE) environment.
2. The input signal edge rate of 2V/ns or greater is to be maintained in the 10% to 90% range of the input waveform.
DIFFERENTIAL INPUT AC TEST CONDITIONS FOR 2.5V LVTTL
NOTES:
1. A nominal 2.5V peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. Compliant devices must
2. A nominal 1.25V crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. Compliant devices must meet the
3. In all cases, input waveform timing is marked at the differential cross-point of the input signals.
4. The input signal edge rate of 2.5V/ns or greater is to be maintained in the 20% to 80% range of the input waveform.
IDT5T905
2.5V SINGLE DATA RATE 1:5 CLOCK BUFFER TERABUFFER
Symbol
Symbol
Symbol
meet the V
V
I
I
X
I
I
I
t
DDQQ
DDDQ
t
V
I
TOTQ
V
V
V
R
DDQ
DDD
R
V
TOT
V
specification under actual use conditions.
THI
DIF
THI
, t
, t
IH
IL
X
F
F
DIF
Quiescent V
Quiescent V
Dynamic V
Current per Output
Dynamic V
Current per Output
Total Power V
Total Power V
(AC) specification under actual use conditions.
Parameter
Input HIGH Voltage
Input LOW Voltage
Input Timing Measurement Reference Level
Input Signal Edge Rate
Parameter
Input Signal Swing
Differential Input Signal Crossing Point
Input Timing Measurement Reference Level
Input Signal Edge Rate
Parameter
DD
DDQ
DD
DDQ
DD
DDQ
Power Supply
Power Supply Current
Power Supply
Power Supply Current
Supply Current
Supply Current
(1)
(2)
(4)
(2)
V
Outputs enabled, All outputs unloaded
V
Outputs enabled, All outputs unloaded
V
V
V
V
V
V
DDQ
DDQ
DD
DD
DDQ
DDQ
DDQ
DDQ
(1)
(3)
= Max., V
= Max., V
= Max., Reference Clock = LOW
= Max., Reference Clock = LOW
= 2.5V, F
= 2.5V, F
= 2.5V, F
= 2.5V, F
Test Conditions
DDQ
DDQ
REFERENCE CLOCK
REFERENCE CLOCK
REFERENCE CLOCK
REFERENCE CLOCK
9
= Max., C
= Max., C
(2)
L
L
= 0pF
= 0pF
= 100MHz, C
= 200MHz, C
= 100MHz, C
= 200MHz, C
(3)
(3)
L
L
L
L
= 15pF
= 15pF
= 15pF
= 15pF
INDUSTRIAL TEMPERATURE RANGE
Crossing Point
Typ.
0.1
20
15
30
20
30
30
70
Value
V
Value
V
V
V
2.5
DD
DD
0
2
DD
DD
/2
/2
(1)
Max
100
0.3
30
20
40
40
50
50
Units
Units
V/ns
V/ns
V
V
V
V
V
V
μA/MHz
μA/MHz
Unit
mA
mA
mA
mA