09 47 474 7201 HARTING, 09 47 474 7201 Datasheet - Page 140

• Manufacturer Part Number: 09 47 474 7201
• Description: Ha-Vis Smart Patch Cable CAT.6 Yel. 1m
• Manufacturer: HARTING

Specifications of 09 47 474 7201

• Rohs Compliant: Yes

140
Crosstalk_MicroTCA.indd 1
AdvancedMC™ connectors for MicroTCA™
Technical characteristics
Design according
Number of contacts
Contact spacing
Clearance and creepage
distance between contacts 0.1 mm min.
Working current of
power contacts
as defined
in MTCA.0 spec.
Test voltage
Working voltage typically 3.3 V; 5.0 V; 12.0 V
Initial contact resistance 25 mW max.
Initial insulation resistance 100 MW min.
Nominal differential
impedance
Differential propagation
delay
Differential skew
Temperature range
Durability as per
MTCA.0 spec.
Termination technique
Mating force
Withdrawal force
Max. NEXT @ 25 ps risetime
Adjacent
Basic-to-extended (diagonal)
Basic-to-extended (opposite)
Multiline (five multi-aggressor
differential pairs)
1.5
1.5
1.5
1.5
2.25
0.2
extended side
ground
basic side
31.03.2008 16:15:27
PICMG MTCA.0 R1.0
(RoHS compliance)
170
0.75 mm
~ 2.3 A @ 70 °C
max. 30 °C temp. rise
(PICMG requirement min. 1.52 A)
80 V
100 W±10 %
Basic side:
Extended side: 70 ps ± 5 ps
Between basic and
extended side:
Within basic and
extended side:
-55 °C … +105 °C
200 mating cycles
Press-in termination
100 N max., typically 60 - 80 N
(depending on AdvancedMC™)
(depending on AdvancedMC™)
65 N max., typically 40 - 60 N
PCB library on request
(PADS/Dx-Designer)
SPICE models and
S-Parameter on request
r.m.s.
Bottom route
2.88 % max.
70 ps ± 5 ps
0.65 %
0.60 %
0.73 %
±2 ps
±2 ps
Materials
Moulded parts
Contacts
Contact surface
Packaging
Recommended plated through hole specification
The press-in zone of the AdvancedMC™ connector is
tested according to Telcordia/Bellcore GR 1217CORE
Part7. It is approved to be used with a plated through
hole according IEC 60352-5 with a diameter of
0.55
Based on our experiences regarding the production
process of the PCB manufacturer we recommend a
plated through hole configuration like shown in the
above spreadsheet. To achieve the recommended
plated through hole diameter, it is important to specify
especially the drilled hole diameter of 0.64
your PCB supplier.
For drillings use e.g. drill bit # 72 (0.025" ≈ 0.64 mm).
Au / Ni plated PCB
Silver plated PCB
Tin plated PCB
Chemical tin
OSP copper
plated PCB
plated PCB
±0.05
(HAL)
mm (drilled hole 0.64
A
B
C
D
C
D
C
D
C
D
C
D
E
Drill hole-Ø
Cu
Sn
Hole-Ø
Ni
Au
Hole-Ø
Sn
Hole-Ø
Ag
Hole-Ø
---
Hole-Ø
Pad size
Liquid Crystal Polymer
(LCP), UL 94-V0
Copper Alloy
Pd/Ni with Au flash
Au over Ni on request
Cardboard box (other
packaging on request)
±0.01
0 .64
25 - 35 µm
5 - 15 µm
0 .53 - 0 .60 mm
3 - 7 µm
0 .05 - 0 .12 µm
0 .55 - 0 .60 mm
0 .8 - 1 .5 µm
0 .56 - 0 .60 mm
0 .1 - 0 .3 µm
0 .56 - 0 .60 mm
---
0 .56 - 0 .60 mm
min . 0 .95 mm
mm).
±0 .01
mm
±0.01
mm to