1469054-1 TE Connectivity, 1469054-1 Datasheet - Page 2

• Manufacturer Part Number: 1469054-1
• Description: HM-ZD 2PR HDR SELECT LOAD
• Manufacturer: TE Connectivity

Specifications of 1469054-1

• Product Type: Connector
• Connector Type: Header
• Pcb Mounting Orientation: Vertical
• Shield Material: Phosphor bronze
• Module Length (mm [in]): 24.90 [0.980]
• Interface Type: HM-Zd
• Termination Method: Press Fit
• Termination End Plating: Tin-Lead over Nickel
• Card Slot Pitch (mm [in]): 20.3 [0.8]
• Columns Per Connector: 10
• Centerline (mm [in]): 2.50 [0.098]
• Selectively Loaded: Yes
• Number Of Positions: 32
• Contact Type: Pin
• Contact Termination Type: Through Hole
• Contact Configuration: ACTION PIN Post
• Feedthrough Post Length (mm [in]): 2.50 [0.098]
• Contact Mating Area Length (mm [in]): 6.35 [0.250]
• Contact Base Material: Phosphor Bronze
• Housing Material: Polyester GF
• Number Of Pairs Per Column: 2
• Number Of Pairs Per Connector: 20
• Sequenced Pins: Yes (See Drawing)
• Advancedtca Specified Product: No
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant

3.2.
3.3.
3.4.
3.5.
Rev C
Initial exam ination of product.
Final exam ination of product.
Low level contact resistance.
Low level com pliant pin resistance.
Insulation resistance.
Materials
Materials used in the construction of this product shall be as specified on the applicable product
drawing.
Ratings
!
!
!
Perform ance and Test Description
Product is designed to m eet the electrical, m echanical and environm ental perform ance requirem ents
specified in Figure 1. Unless otherwise specified, all tests shall be perform ed at am bient environm ental
conditions per EIA-364.
Test Requirem ents and Procedures Sum m ary
Test Description
Operating Voltage: 250 volts AC m axim um peak (a of m inim um breakdown voltage)
Current: .7 am pere per contact (fully loaded)
Tem perature: -65 to 105°C
Meets requirem ents of product
drawing.
Meets visual requirem ents.
20 m illiohm s m axim um initial for
right angle receptacle and vertical
header.
50 m illiohm s m axim um initial for
right angle receptacle and right
angle header.
ÄR < 5 m illiohm s average final.
ÄR < 10 m illiohm s individual
reading final (applies to both signal
and ground contacts).
1 m illiohm m axim um initial.
ÄR = 1 m illiohm m axim um change
from initial.
10000 m egohm s m inim um .
Figure 1 (continued)
ELECTRICAL
Requirem ent
EIA-364-18.
EIA-364-21.
EIA-364-18.
Visual and dim ensional © of C)
inspection per product drawing.
Visual inspection.
EIA-364-23.
Subject specim ens to 100
m illiam peres m axim um and 20
m illivolts m axim um open circuit
voltage.
See Figure 3.
EIA-364-23.
Subject specim ens to 100
m illiam peres m axim um and 20
m illivolts m axim um open circuit
voltage. Measurem ents shall be
taken between PCB hole and pin
tip.
Test between any adjacent signal
contacts, and between any signal
contact and adjacent ground
contacts at 100 volts DC.
Specim ens shall be fully m ated.
Procedure
108-2055
2 of 8