M48T35AV-10MH1F STMicroelectronics, M48T35AV-10MH1F Datasheet - Page 15
![IC TIMEKPR NVRAM 256KB 3V 28SOIC](/photos/6/56/65690/stmicroelectronics-28-soic_sml.jpg)
M48T35AV-10MH1F
Manufacturer Part Number
M48T35AV-10MH1F
Description
IC TIMEKPR NVRAM 256KB 3V 28SOIC
Manufacturer
STMicroelectronics
Series
Timekeeper®r
Type
Clock/Calendar/NVSRAMr
Datasheet
1.M4T28-BR12SH1.pdf
(29 pages)
Specifications of M48T35AV-10MH1F
Memory Size
256K (32K x 8)
Time Format
HH:MM:SS (24 hr)
Date Format
YY-MM-DD-dd
Interface
Parallel
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
28-SOIC, 28-SOH (8.48mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-4714-2
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M48T35AV-10MH1F
Manufacturer:
ST
Quantity:
5 510
Company:
Part Number:
M48T35AV-10MH1F
Manufacturer:
NSC
Quantity:
5 510
M48T35AV
Note:
3.5
Note:
occurs within a 64 minute cycle. The first 62 minutes in the cycle may, once per minute, have
one second either shortened by 128 or lengthened by 256 oscillator cycles. If a binary '1' is
loaded into the register, only the first 2 minutes in the 64 minute cycle will be modified; if a
binary 6 is loaded, the first 12 will be affected, and so on.
Therefore, each calibration step has the effect of adding 512 or subtracting 256 oscillator
cycles for every 125,829,120 actual oscillator cycles, that is +4.068 or –2.034 ppm of
adjustment per calibration step in the calibration register. Assuming that the oscillator is in
fact running at exactly 32,768 Hz, each of the 31 increments in the calibration byte would
represent +10.7 or –5.35 seconds per month which corresponds to a total range of +5.5 or –
2.75 minutes per month.
Two methods are available for ascertaining how much calibration a given M48T35AV may
require. The first involves simply setting the clock, letting it run for a month and comparing it
to a known accurate reference (like WWV broadcasts). While that may seem crude, it allows
the designer to give the end user the ability to calibrate his clock as his environment may
require, even after the final product is packaged in a non-user serviceable enclosure.
The second approach is better suited to a manufacturing environment, and involves the use
of some test equipment. When the FREQUENCY TEST (FT) bit, the seventh-most
significant bit in the day register is set to a '1,' and D7 of the seconds register is a '0'
(oscillator running), DQ0 will toggle at 512 Hz during a READ of the seconds register. Any
deviation from 512 Hz indicates the degree and direction of oscillator frequency shift at the
test temperature. For example, a reading of 512.01024 Hz would indicate a +20 ppm
oscillator frequency error, requiring a –10 (WR001010) to be loaded into the calibration byte
for correction.
Setting or changing the calibration byte does not affect the frequency test output frequency.
The FT bit MUST be reset to '0' for normal clock operations to resume. The FT bit is
automatically reset on power-down.
For more information on calibration, see application note AN934, “TIMEKEEPER
Calibration.”
Century bit
Bit D5 and D4 of clock register 7FFCh contain the CENTURY ENABLE bit (CEB) and the
CENTURY bit (CB). Setting CEB to a '1' will cause CB to toggle, either from a '0' to '1' or
from '1' to '0' at the turn of the century (depending upon its initial state). If CEB is set to a '0,'
CB will not toggle.
The WRITE bit must be set in order to write to the CENTURY bit.
Doc ID 6845 Rev 8
Clock operations
®
15/29