DS1386P-8-120+ Maxim Integrated Products, DS1386P-8-120+ Datasheet - Page 6
![IC TIMEKEEPER RAM 64K 34-PCM](/photos/6/58/65856/406-34-pcm_sml.jpg)
DS1386P-8-120+
Manufacturer Part Number
DS1386P-8-120+
Description
IC TIMEKEEPER RAM 64K 34-PCM
Manufacturer
Maxim Integrated Products
Type
Clock/Calendar/NVSRAMr
Datasheet
1.DS1386-32-120.pdf
(21 pages)
Specifications of DS1386P-8-120+
Memory Size
64K (8K x 8)
Time Format
HH:MM:SS:hh (12/24 hr)
Date Format
YY-MM-DD-dd
Interface
Parallel
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
34-PowerCap™ Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
DS1386/1386P
TIME-OF-DAY REGISTERS
Registers 0 through A contain time, date, and alarm data in BCD. Fifteen bits within these 11 registers are
not used and will always read 0 regardless of how they are written. Bits 6 and 7 in the Months Register
(9) are binary bits. When set to logic 0, EOSC (Bit 7) enables the RTC oscillator. This bit is set to logic 1
as shipped from Dallas Semiconductor to prevent lithium energy consumption during storage and
shipment (DIP Module only). This bit will normally be turned on by the user during device initialization.
However, the oscillator can be turned on and off as necessary by setting this bit to the appropriate level.
Bit 6 of this same byte controls the square wave output. When set to logic 0, the square wave output pin
will output a 1024Hz square wave signal. When set to logic 1 the square wave output pin is in a high
impedance state. Bit 6 of the Hours Register is defined as the 12- or 24-hour select bit. When set to logic
1, the 12-hour format is selected. In the 12-hour format, bit 5 is the AM/PM bit with logic 1 being PM. In
the 24-hour mode, bit 5 is the second 10-hour bit (20-23 hours). The Time of Day Registers are updated
every 0.01 seconds from the Real Time Clock, except when the TE bit (bit 7 of Register B) is set low or
the clock oscillator is not running. The preferred method of synchronizing data access to and from the
RAMified Timekeeper is to access the Command Register by doing a write cycle to address location 0B
and setting the TE bit (transfer enable bit) to a logic 0. This will freeze the External Time of Day
Registers at the present recorded time, allowing access to occur without danger of simultaneous update.
When the watch registers have been read or written, a second write cycle to location 0B, setting the TE
bit to a logic 1, will put the Time of Day Registers back to being updated every 0.01 second. No time is
lost in the Real Time Clock because the internal copy of the Time of Day Register buffers is continually
incremented while the external memory registers are frozen. An alternate method of reading and writing
the Time of Day Registers is to ignore synchronization. However, any single read may give erroneous
data as the Real Time Clock may be in the process of updating the external memory registers as data is
being read. The internal copies of seconds through years are incremented, and the time of day alarm is
checked during the period that hundreds of seconds reads 99 and are transferred to the external register
when hundredths of seconds roll from 99 to 00. A way of making sure data is valid is to do multiple reads
and compare. Writing the registers can also produce erroneous results for the same reasons. A way of
making sure that the write cycle has caused proper update is to do read verifies and re-execute the write
cycle if data is not correct. While the possibility of erroneous results from reads and write cycles has been
stated, it is worth noting that the probability of an incorrect result is kept to a minimum due to the
redundant structure of the RAMified Timekeeper.
TIME-OF-DAY ALARM REGISTERS
Registers 3, 5, and 7 contain the Time of Day Alarm Registers. Bits 3, 4, 5, and 6 of Register 7 will
always read 0 regardless of how they are written. Bit 7 of Registers 3, 5, and 7 are mask bits (Table 1).
When all of the mask bits are logic 0, a Time of Day Alarm will only occur when Registers 2, 4, and 6
match the values stored in Registers 3, 5, and 7. An alarm will be generated every day when bit 7 of
Register 7 is set to a logic 1. Similarly, an alarm is generated every hour when bit 7 of Registers 7 and 5
is set to a logic 1. When bit 7 of Registers 7, 5, and 3 is set to a logic 1, an alarm will occur every minute
when Register 1 (seconds) rolls from 59 to 00.
Time of Day Alarm Registers are written and read in the same format as the Time of Day Registers. The
Time of Day Alarm Flag and Interrupt are always cleared when Alarm Registers are read or written.
6 of 21