LTC1407CMSE-1#TR Linear Technology, LTC1407CMSE-1#TR Datasheet
LTC1407CMSE-1#TR
Specifications of LTC1407CMSE-1#TR
Available stocks
Related parts for LTC1407CMSE-1#TR
LTC1407CMSE-1#TR Summary of contents
Page 1
... The serial interface sends out the two conversion results in 32 clocks for compatibility with standard serial interfaces. L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. ...
Page 2
... LTC1407I-1/LTC1407AI-1 .....................–40°C to 85°C Storage Temperature Range ...................–65°C to 150°C Lead Temperature (Soldering, 10 sec) .................. 300°C ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL LTC1407CMSE-1#PBF LTC1407CMSE-1#TRPBF LTC1407IMSE-1#PBF LTC1407IMSE-1#TRPBF LTC1407ACMSE-1#PBF LTC1407ACMSE-1#TRPBF LTC1407AIMSE-1#PBF LTC1407AIMSE-1#TRPBF Consult LTC Marketing for parts specifi ed with wider operating temperature ranges. ...
Page 3
ANALOG INPUT l The denotes the specifi cations which apply over the full operating temperature range, otherwise specifi cations are 25°C. With internal reference SYMBOL PARAMETER V Analog Differential Input Range (Notes ...
Page 4
LTC1407-1/LTC1407A-1 INTERNAL REFERENCE CHARACTERISTICS PARAMETER V Output Voltage REF V Output Tempco REF V Line Regulation REF V Output Resistance REF V Setting Time REF DIGITAL INPUTS AND DIGITAL OUTPUTS full operating temperature range, otherwise specifi cations are at T ...
Page 5
TIMING CHARACTERISTICS range, otherwise specifi cations are SYMBOL PARAMETER f Maximum Sampling Frequency per Channel SAMPLE(MAX) (Conversion Rate) t Minimum Sampling Period (Conversion + Acquisition Period) THROUGHPUT t Clock Period SCK t Conversion Time CONV t Minimum ...
Page 6
LTC1407-1/LTC1407A-1 TYPICAL PERFORMANCE CHARACTERISTICS +CH0/+CH1 with –CH0/–CH1 = 1.5V DC, differential signals drive both inputs with V ENOBs and SINAD vs Input Sinewave Frequency 12.0 11.5 11.0 10.5 10.0 9.5 9.0 8.5 8.0 0 100 FREQUENCY (MHz) 14071 ...
Page 7
TYPICAL PERFORMANCE CHARACTERISTICS +CH0/+CH1 with –CH0/–CH1 = 1.5V DC, differential signals drive both inputs with V 1403kHz Input Summed with 1563kHz Input IMD 4096 Point FFT Plot for Differential Input Signals 0 –10 –20 –30 –40 –50 –60 –70 –80 ...
Page 8
LTC1407-1/LTC1407A-1 TYPICAL PERFORMANCE CHARACTERISTICS +CH0/+CH1 with –CH0/–CH1 = 1.5V DC, differential signals drive both inputs with V Differential and Integral Linearity vs Conversion Rate MIN DNL –1 MIN INL –2 –3 ...
Page 9
TYPICAL PERFORMANCE CHARACTERISTICS Reference Voltage vs V 2.4902 2.4900 2.4898 2.4896 2.4894 2.4892 2.4890 2.6 2.8 3 PIN FUNCTIONS + CH0 (Pin 1): Noninverting Channel 0. CH0 fully differentially with respect to CH0 1.25V differential swing with respect ...
Page 10
LTC1407-1/LTC1407A-1 BLOCK DIAGRAM + + CH0 1 S & H – CH0 – CH1 4 S & H – – CH1 5 V REF 3 10μF GND 6 EXPOSED PAD 11 10 10μ ...
Page 11
TIMING DIAGRAMS LTC1407-1/LTC1407A-1 14071fb 11 ...
Page 12
LTC1407-1/LTC1407A-1 TIMING DIAGRAMS SCK CONV NAP SCK CONV NAP SLEEP V REF NOTE: NAP AND SLEEP ARE INTERNAL SIGNALS SCK SDO 12 Nap Mode Waveforms t 1 Sleep Mode Waveforms t 1 SCK to SDO Delay SCK ...
Page 13
... LT1810: 180MHz GBWP , –90dBc distortion at 5MHz, unity-gain stable, rail-to-rail in and out, 15mA/amplifi er, 16nV/√Hz. LinearView is a trademark of Linear Technology Corporation. , 500μV offset and VOL = 5V), making the part excellent for ...
Page 14
LTC1407-1/LTC1407A-1 APPLICATIONS INFORMATION LT1818/LT1819: 400MHz, 2500V/μs, 9mA, Single/Dual Voltage Mode Operational Amplifi er. LT6200: 165MHz GBWP , –85dBc distortion at 1MHz, unity-gain stable, rail-to-rail in and out, 15mA/amplifi er, 0.95nV/√Hz. LT6203: 100MHz GBWP , –80dBc distortion at 1MHz, unity-gain stable, ...
Page 15
APPLICATIONS INFORMATION INTERNAL REFERENCE The LTC1407-1/LTC1407A-1 have an on-chip, temperature compensated, bandgap reference that is factory trimmed near 2.5V to obtain a precise ±1.25V input span. The ref- erence amplifi er output V , (Pin 3) must be bypassed REF ...
Page 16
LTC1407-1/LTC1407A-1 APPLICATIONS INFORMATION 5V C5 0.1μF C3 – 1μF U1 1/2 LT1819 1.25V P-P C6 MAX 0.1μ –5V 499Ω 499Ω C4 – 1μF U2 1/2 LT1819 + Figure 6a. The LT1819 Driving the LTC1407A-1 Differentially ...
Page 17
APPLICATIONS INFORMATION at the LTC1407-1/LTC1407A-1 Exposed Pad. The ground return from the LTC1407-1/LTC1407A-1 Pin 6 to the power supply should be low impedance for noise-free operation. The Exposed Pad of the 10-lead MSE package is also tied to Pin 6 ...
Page 18
LTC1407-1/LTC1407A-1 APPLICATIONS INFORMATION Serial Clock Input (SCK) The rising edge of SCK advances the conversion process and also updates each bit in the SDO data stream. After CONV rises, the third rising edge of SCK sends out two sets of ...
Page 19
APPLICATIONS INFORMATION ; 12-03-03 ****************************************************************** ; Files: 014SIAB.ASM -> 1407A Sine wave collection with Serial Port interface ; bvectors.asm both channels collected in sequence in the same 2k record. ; s2k14ini.asm Buffered mode 2k buffer size. ; First element at ...
Page 20
LTC1407-1/LTC1407A-1 APPLICATIONS INFORMATION ; ——————— mask and shift input data —————————————— bufull *ar3+ << #07FFFh & #2000h ; *ar2+ = data(#0bh (@ar2 == #02000h) if (TC) goto start ...
Page 21
APPLICATIONS INFORMATION .title “Vector Table” .mmregs reset goto #80h ;00; RESET nop nop nmi return_enable ;04; non-maskable external interrupt nop nop nop trap2 goto #88h ;08; trap2 nop nop .space 52*16 ;0C-3F: vectors for software interrupts 18-30 int0 return_enable ;40; ...
Page 22
LTC1407-1/LTC1407A-1 APPLICATIONS INFORMATION .space 24*16 ;68-7F; reserved area ********************************************************************** * (C) COPYRIGHT TEXAS INSTRUMENTS, INC. 1996 ********************************************************************** * * File: s2k14ini.ASM BSP initialization code for the ‘C54x DSKplus * for use with 1407 in buffered mode * BSPC and SPC ...
Page 23
APPLICATIONS INFORMATION * 2’ cable from counter to CLK at DUT *No right shift is needed to right justify the input data in the main program * *the two msbs should also be masked * ******************************************************************************************* * Loopback .set NO ...
Page 24
LTC1407-1/LTC1407A-1 PACKAGE DESCRIPTION 2.794 0.102 (.110 .004) 5.23 (.206) MIN 0.305 0.038 (.0120 .0015) TYP RECOMMENDED SOLDER PAD LAYOUT DETAIL “A” 0.254 (.010) GAUGE PLANE 0.18 (.007) NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES ...
Page 25
... Update Pin Confi guration Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa- tion that the interconnection of its circuits as described herein will not infringe on existing patent rights. LTC1407-1/LTC1407A-1 ...
Page 26
... Serial SoftSpan™ I References LT1790-2.5 Micropower Series Reference in SOT-23 LT1461-2.5 Precision Voltage Reference LT1460-2.5 Micropower Series Voltage Reference SoftSpan is a trademark of Linear Technology Corporation. 26 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 ● COMMENTS ±5V Supply, ±2.5V Span, 90dB SINAD 5V Confi ...