LTC1400CS8 Linear Technology, LTC1400CS8 Datasheet
LTC1400CS8
Specifications of LTC1400CS8
Available stocks
Related parts for LTC1400CS8
LTC1400CS8 Summary of contents
Page 1
... The 3-wire serial port allows compact and efficient data transfer to a wide range of microprocessors, microcon- trollers and DSPs. , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners ...
Page 2
... A CONV CLK 3 6 REF GND OUT S8 PACKAGE 8-LEAD PLASTIC 150°C, θ = 130°C/W JMAX JA S8 PART MARKING LTC1400CS8 1400 LTC1400IS8 1400I http://www.linear.com/leadfree/ MIN TYP MAX 4.75 4.75 –2.45 –5.25 15 ● 1.0 ● 5.0 ● 0.3 ● 0.2 ● 1 ● ...
Page 3
CO VERTER CHARACTERISTICS U temperature range, otherwise specifications are at T PARAMETER CONDITIONS Resolution (No Missing Codes) Integral Linearity Error (Note 9) Differential Linearity Error Offset Error (Note 10) Full-Scale Error Full-Scale Tempco I OUT(REF ACCURACY U ...
Page 4
LTC1400 DIGITAL I PUTS A D DIGITAL OUTPUTS U U full operating temperature range, otherwise specifications are at T SYMBOL PARAMETER V Low Level Output Voltage OL I Hi-Z Output Leakage D OZ OUT C Hi-Z Output Capacitance D OZ ...
Page 5
TYPICAL PERFOR A CE CHARACTERISTICS W U Differential Nonlinearity vs Output Code 1. 400kHz SAMPLE 0.75 0.50 0.25 0 –0.25 –0.50 –0.75 –1.00 0 512 1024 1536 2048 2560 3072 3584 4096 OUTPUT CODE 1400 TPC01 Signal-to-Noise Ratio ...
Page 6
LTC1400 PI FU CTIO (Pin 1): Positive Supply, 5V. Bypass to GND (10μF CC tantalum in parallel with 0.1μF ceramic). A (Pin 2): Analog Input 4.096V (Unipolar), ±2.048V IN (Bipolar). V (Pin 3): ...
Page 7
APPLICATIO S I FOR ATIO U U Conversion Details The LTC1400 uses a successive approximation algorithm and an internal sample-and-hold circuit to convert an analog signal to a 12-bit serial output based on a preci- sion internal reference. The control ...
Page 8
LTC1400 APPLICATIO S I FOR ATIO 400kHz SAMPLE – 199.121kHz IN –20 SINAD = 72.1dB THD = – 80dB –30 –40 –50 –60 –70 –80 –90 –100 –110 –120 ...
Page 9
... The following list is a summary of the op amps that are suitable for driving the LTC1400, more detailed informa- 1400 F05 tion is available in the Linear Technology databooks or the Linear Technology Website. LT1215/LT1216: Dual and quad 23MHz, 50V/μs single supply op amps. Single 5V to ±15V supplies, 6.6mA specifi ...
Page 10
LTC1400 APPLICATIO S I FOR ATIO U U trimmed to 2.42V internally connected to the DAC and is available at Pin 3 to provide up to 1mA of current to an external load. For minimum code transition noise, ...
Page 11
APPLICATIO S I FOR ATIO 50Ω – 100Ω 10k R3 10k FULL-SCALE ADJUST ADDITIONAL PINS OMITTED FOR CLARITY ±20LSB TRIM RANGE Figure 10a. LTC1400 Full-Scale Adjust Circuit R1 10k ANALOG + ...
Page 12
LTC1400 APPLICATIO S I FOR ATIO U U Input signal leads to A and signal return leads from GND IN (Pin 4) should be kept as short as possible to minimize noise coupling. In applications where this is not possible, ...
Page 13
APPLICATIO S I FOR ATIO the Sleep mode, power consumption is reduced to a minimum by cutting off the supply to all internal circuitry including the reference. Figure 12 shows the ways to power down the LTC1400. ...
Page 14
LTC1400 TYPICAL APPLICATIO S U Hardware Interface to TMS320C50’s TDM Serial Port (Frame Sync is Generated from TFSX) + 10µF Logic Analyzer Waveforms Show 3.2μs Throughput Rate (Input Voltage = 3.046V, Output Code = 1011 1110 0110 = 3046 Data ...
Page 15
TYPICAL APPLICATIO S U THIS PROGRAM DEMONSTRATES LTC1400 INTERFACE TO TMS320C50 FRAME SYNC PULSE IS GENERATED FROM TFSX *Initialization* .mmregs ; Defines global symbolic names ;- - Initialized data memory to zero .ds 0F00h ; Initialize data to zero DATA0 ...
Page 16
LTC1400 TYPICAL APPLICATIO S U LTC1400 Interface to ADSP2181’s SPORT0 (Frame Sync is Generated from RFS0) + 10µF Logic Analyzer Waveforms Show 2.88μs Throughput Rate (Input Voltage = 2.240V, Output Code = 1000 1100 0000 = 2240 X RDY Data ...
Page 17
TYPICAL APPLICATIO S U THIS PROGRAM DEMONSTRATES LTC1400 INTERFACE TO ADSP-2181 FRAME SYNC PULSE IS GENERATED FROM RFS0 /*Section 1: Initialization*/ .module/ram/abs = 0 adspltc; /*define the program module*/ jump start; /*jump over interrupt vectors*/ nop; nop; nop; rti; rti; ...
Page 18
LTC1400 TYPICAL APPLICATIO S U Quick Look Circuit for Converting Data to Parallel Format 5V + 10µF ANALOG INPUT (0V TO 4.096V) 2.42V REFERENCE + OUTPUT 10µF 0.1µ CONV 0.1µF LTC1400 7 CONV ...
Page 19
... FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa- tion that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 20
... Inputs, MSOP and SO-8 1.22mW, 1-/2-Channel Inputs, MSOP and SO-8 4.25mW, 1-/2-Channel Inputs, MSOP and SO-8 www.linear.com ● TMS320C50 TCLKX TCLKR TFSX TFSR TDR 1400 TA04a ADSP2181 SCLKO RFSO DR0 1400 TA05a LT 0606 REV A • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2006 1400fa ...