AD7730BRUZ Analog Devices Inc, AD7730BRUZ Datasheet - Page 21

• Manufacturer Part Number: AD7730BRUZ
• Description: IC ADC TRANSDUCER BRIDGE 24TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD7730BRUZ

• Data Interface: DSP, Serial, SPI™
• Number Of Bits: 24
• Sampling Rate (per Second): 1.2k
• Number Of Converters: 1
• Power Dissipation (max): 125mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-TSSOP (0.173", 4.40mm Width)
• Resolution (bits): 24bit
• Input Channel Type: Differential, Single Ended
• Supply Voltage Range - Analog: 4.75V To 5.25V
• Supply Voltage Range - Digital: 2.7V To 5.25V
• Number Of Elements: 1
• Resolution: 24Bit
• Architecture: Delta-Sigma
• Sample Rate: 1.2KSPS
• Input Polarity: Unipolar/Bipolar
• Input Type: Voltage
• Differential Input: Yes
• Power Supply Requirement: Analog and Digital
• Single Supply Voltage (typ): 5V
• Single Supply Voltage (min): 4.75V
• Single Supply Voltage (max): 5.25V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Dissipation: 125mW
• Integral Nonlinearity Error: 18ppm of FSR
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 24
• Package Type: TSSOP
• Input Signal Type: Differential
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7730LEBZ - BOARD EVALUATION FOR AD7730EVAL-AD7730EBZ - BOARD EVAL FOR AD7730
• Lead Free Status / Rohs Status: Compliant

REV. A
READING FROM AND WRITING TO THE ON-CHIP REGISTERS
The AD7730 contains a total of thirteen on-chip registers. These registers are all accessed over a three-wire interface. As a result,
addressing of registers is via a write operation to the topmost register on the part, the Communications Register. Figure 5 shows a
flowchart for reading from the different registers on the part summarizing the sequence and the words to be written to access each of
the registers. Figure 6 gives a flowchart for writing to the different registers on the part, again summarizing the sequence and words
to be written to the AD7730.
(SEE ACCOMPANYING TABLE)
COMMUNICATIONS REGISTER
WRITE BYTE W TO
READ REGISTER
CONTINUOUS
REQUIRED?
READS OF
REGISTER
START
COMMUNICATIONS REGISTER
(SEE ACCOMPANYING TABLE)
NO
WRITE TO REGISTER
WRITE BYTE Y TO
START
END
YES
Figure 5. Flowchart for Reading from the AD7730 Registers
(SEE ACCOMPANYING TABLE)
COMMUNICATIONS REGISTER
COMMUNICATIONS REGISTER
(SEE ACCOMPANYING TABLE)
NO
Figure 6. Flowchart for Writing to the AD7730 Registers
WRITE BYTE Y TO
WRITE BYTE Z TO
READ REGISTER
CONTINUOUS
OPERATION?
READ
STOP
YES
Register
Communications Register
Data Register
Mode Register
Filter Register
DAC Register
Offset Register
Gain Register
Test Register
–21–
Register
Status Register
Data Register
Mode Register
Filter Register
DAC Register
Offset Register
Gain Register
Test Register
*N/A= Not Applicable. Continuous reads of these registers does not make sense
as the register contents would remain the same since they are only changed by a
write operation.
Byte Y (Hex)
00
Read Only Register
02
03
04
05
06
User is advised not to change
contents of Test Register.
Byte W
10
11
12
(Hex)
13
14
15
16
17
AD7730/AD7730L
Byte Y
(Hex)
20
21
22
N/A*
N/A*
N/A*
N/A*
N/A*
Byte Z
(Hex)
30
30
30
N/A*
N/A*
N/A*
N/A*
N/A*