AD9411BSV-200 Analog Devices Inc, AD9411BSV-200 Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9411BSV-200
Manufacturer Part Number
AD9411BSV-200
Description
IC ADC 10BIT 200MSPS 100-TQFP
Manufacturer
Analog Devices Inc
Datasheet
1.AD9411BSVZ-170.pdf
(28 pages)
Specifications of AD9411BSV-200
Rohs Status
RoHS non-compliant
Number Of Bits
10
Sampling Rate (per Second)
200M
Data Interface
Parallel
Number Of Converters
1
Power Dissipation (max)
1.59W
Voltage Supply Source
Single Supply
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
100-TQFP Exposed Pad
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD9411BSV-200
Manufacturer:
ADI
Quantity:
210
AD9411
TERMINOLOGY
Analog Bandwidth
The analog input frequency at which the spectral power of the
fundamental frequency (as determined by the FFT analysis) is
reduced by 3 dB.
Aperture Delay
The delay between the 50% point of the rising edge of the clock
command and the instant at which the analog input is sampled.
Aperture Uncertainty (Jitter)
The sample-to-sample variation in aperture delay.
Crosstalk
Coupling onto one channel being driven by a low level (–40 dBFS)
signal when the adjacent interfering channel is driven by a full-
scale signal.
Differential Analog Input Resistance, Differential Analog
Input Capacitance, and Differential Analog Input Impedance
The real and complex impedances measured at each analog
input port. The resistance is measured statically and the
capacitance and differential input impedances are measured
with a network analyzer.
Differential Analog Input Voltage Range
The peak-to-peak differential voltage that must be applied to
the converter to generate a full-scale response. Peak differential
voltage is computed by observing the voltage on a single pin
and subtracting the voltage from the other pin, which is 180°
out of phase. Peak-to-peak differential is computed by rotating
the input’s phase 180° and again taking the peak measurement.
The difference is then computed between both peak
measurements.
Differential Nonlinearity
The deviation of any code width from an ideal 1 LSB step.
Effective Number of Bits (ENOB)
Calculated from the measured SNR based on the equation
ENOB
=
SNR
MEASURED
. 6
02
−
. 1
76
dB
Rev. A | Page 10 of 28
Clock Pulse Width/Duty Cycle
Pulse width high is the minimum amount of time the clock
pulse should be left in the Logic 1 state to achieve rated
performance; pulse width low is the minimum time the clock
pulse should be left in the low state. Refer to the timing
implications of changing t
Input section. At a given clock rate, these specifications define
an acceptable CLOCK duty cycle.
Full-Scale Input Power
Expressed in dBm. Computed using the following equation:
Gain Error
The difference between the measured and ideal full-scale input
voltage range of the ADC.
Harmonic Distortion, Second
The ratio of the rms signal amplitude to the rms value of the
second harmonic component, reported in dBc.
Harmonic Distortion, Third
The ratio of the rms signal amplitude to the rms value of the
third harmonic component, reported in dBc.
Integral Nonlinearity
The deviation of the transfer function from a reference line
measured in fractions of 1 LSB using a “best straight line”
determined by a least square curve fit.
Minimum Conversion Rate
The CLOCK rate at which the SNR of the lowest analog signal
frequency drops by no more than 3 dB below the guaranteed
limit.
Maximum Conversion Rate
The CLOCK rate at which parametric testing is performed.
Output Propagation Delay
The delay between a differential crossing of CLK+ and CLK–
and the time when all output data bits are within valid logic
levels.
Power
FULLSCALE
=
ENCH
10
in the Application Notes, Clock
log
⎛
⎜
⎜
⎜
⎜
⎝
V
2
FULLSCALE
Z
. 0
INPUT
001
RMS
⎞
⎟
⎟
⎟
⎟
⎠