MCP4551T-503E/MF Microchip Technology, MCP4551T-503E/MF Datasheet - Page 56
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
MCP4551T-503E/MF
Manufacturer Part Number
MCP4551T-503E/MF
Description
IC DGTL POT 50K 256TAPS 8-DFN
Manufacturer
Microchip Technology
Datasheet
1.MCP4531-104EMS.pdf
(88 pages)
Specifications of MCP4551T-503E/MF
Package / Case
8-DFN
Taps
257
Resistance (ohms)
50K
Number Of Circuits
1
Temperature Coefficient
150 ppm/°C Typical
Memory Type
Volatile
Interface
I²C, 2-Wire Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Resistance In Ohms
50K
Number Of Pots
Single
Taps Per Pot
256
Resistance
50 KOhms
Wiper Memory
Volatile
Digital Interface
Serial (2-Wire, I2C)
Operating Supply Voltage
2.5 V, 3.3 V, 5 V
Supply Current
2.5 uA
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Supply Voltage (max)
5.5 V
Supply Voltage (min)
1.8 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
MCP4551T-503E/MFTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MCP4551T-503E/MF
Manufacturer:
Microchip
Quantity:
3 287
MCP453X/455X/463X/465X
7.4
The Write Command can be issued to both the Volatile
and Non-Volatile memory locations. The format of the
command, see
Byte, an A bit, the MCP4XXX Command Byte, an A bit,
the MCP4XXX Data Byte, an A bit, and a Stop (or
Restart) condition. The MCP4XXX generates the A / A
bits.
A Write command to a Volatile memory location
changes that location after a properly formatted Write
Command and the A / A clock have been received.
7.4.1
For volatile memory locations, data is written to the
MCP4XXX after every byte transfer (during the
Acknowledge). If a Stop or Restart condition is gener-
ated during a data transfer (before the A), the data will
not be written to the MCP4XXX. After the A bit, the
master can initiate the next sequence with a Stop or
Restart condition.
Refer to
DS22096A-page 56
Figure 7-2
Write Data
Normal and High Voltage
SINGLE WRITE TO VOLATILE
MEMORY
Figure
for the byte write sequence.
7-2, includes the I
2
C Control
7.4.2
A continuous write mode of operation is possible when
writing to the volatile memory registers (address 00h,
01h, and 04h). This continuous write mode allows
writes without a Stop or Restart condition or repeated
transmissions of the I
shows the sequence for three continuous writes. The
writes do not need to be to the same volatile memory
address. The sequence ends with the master sending
a STOP or RESTART condition.
7.4.3
The High Voltage Command (HVC) signal is
multiplexed with Address 0 (A0) and is used to indicate
that the command, or sequence of commands, are in
the High Voltage operational state. High Voltage
commands allow the device’s WiperLock Technology
and write protect features to be enabled and disabled.
The HVC pin has an internal resistor connection to the
MCP45XX/46XXs internal V
CONTINUOUS WRITES TO
VOLATILE MEMORY
THE HIGH VOLTAGE COMMAND
(HVC) SIGNAL
© 2008 Microchip Technology Inc.
2
C Control Byte.
DD
signal.
Figure 7-3