MCP4551T-503E/MF Microchip Technology, MCP4551T-503E/MF Datasheet - Page 64
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
MCP4551T-503E/MF
Manufacturer Part Number
MCP4551T-503E/MF
Description
IC DGTL POT 50K 256TAPS 8-DFN
Manufacturer
Microchip Technology
Datasheet
1.MCP4531-104EMS.pdf
(88 pages)
Specifications of MCP4551T-503E/MF
Package / Case
8-DFN
Taps
257
Resistance (ohms)
50K
Number Of Circuits
1
Temperature Coefficient
150 ppm/°C Typical
Memory Type
Volatile
Interface
I²C, 2-Wire Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Resistance In Ohms
50K
Number Of Pots
Single
Taps Per Pot
256
Resistance
50 KOhms
Wiper Memory
Volatile
Digital Interface
Serial (2-Wire, I2C)
Operating Supply Voltage
2.5 V, 3.3 V, 5 V
Supply Current
2.5 uA
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Supply Voltage (max)
5.5 V
Supply Voltage (min)
1.8 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
MCP4551T-503E/MFTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MCP4551T-503E/MF
Manufacturer:
Microchip
Quantity:
3 287
MCP453X/455X/463X/465X
8.2
Figure 8-3
the independent terminals could be used. Disconnect-
ing the wiper allows the transistor input to be taken to
the Bias voltage level (disconnecting A and or B may be
desired to reduce system current). Disconnecting Ter-
minal A modifies the transistor input by the R
stat value to the Common B. Disconnecting Terminal B
modifies the transistor input by the R
to the Common A. The Common A and Common B
connections could be connected to V
FIGURE 8-3:
using Terminal Disconnects.
8.3
At times it may become necessary to perform a Soft-
ware Reset Sequence to ensure the MCP45XX/46XX
device is in a correct and known I
This technique only resets the I
This is useful if the MCP45XX/46XX device powers up
in an incorrect state (due to excessive bus noise, ...), or
if the Master Device is reset during communication.
Figure 8-4
ware reset the device.
DS22096A-page 64
Input
Note:
Input
Using Shutdown
Software Reset Sequence
shows the communication sequence to soft-
shows a possible application circuit where
Balance
This technique is documented in AN1028.
B
A
Common A
Common B
Example Application Circuit
W
2
Bias
C state machine.
2
C Interface state.
AW
DD
To base
of Transistor
(or Amplifier)
rheostat value
and V
BW
SS
.
rheo-
FIGURE 8-4:
Format.
The 1st Start bit will cause the device to reset from a
state in which it is expecting to receive data from the
Master Device. In this mode, the device is monitoring
the data bus in Receive mode and can detect the Start
bit forces an internal Reset.
The nine bits of ‘1’ are used to force a Reset of those
devices that could not be reset by the previous Start bit.
This occurs only if the MCP45XX/46XX is driving an A
bit on the I
command) and is driving a data bit of ‘0’ onto the I
bus. In both of these cases, the previous Start bit could
not be generated due to the MCP45XX/46XX holding
the bus low. By sending out nine ‘1’ bits, it is ensured
that the device will see a A bit (the Master Device does
not drive the I
by the MCP45XX/46XX), which also forces the
MCP45XX/46XX to reset.
The 2nd Start bit is sent to address the rare possibility
of an erroneous write. This could occur if the Master
Device was reset while sending a Write command to
the MCP45XX/46XX, AND then as the Master Device
returns to normal operation and issues a Start condition
while the MCP45XX/46XX is issuing an Acknowledge.
In this case, if the 2nd Start bit is not sent (and the Stop
bit was sent) the MCP45XX/46XX could initiate a write
cycle.
The Stop bit terminates the current I
MCP45XX/46XX wait to detect the next Start condition.
This sequence does not effect any other I
which may be on the bus, as they should disregard this
as an invalid command.
Start
bit
Note:
S
‘1’ ‘1’ ‘1’ ‘1’ ‘1’ ‘1’ ‘1’ ‘1’
2
The potential for this erroneous write
ONLY occurs if the Master Device is reset
while sending a Write command to the
MCP45XX/46XX.
C bus, or is in output mode (from a Read
2
C bus low to acknowledge the data sent
Nine bits of ‘1’
Software Reset Sequence
© 2008 Microchip Technology Inc.
Stop bit
Start bit
2
C bus activity. The
2
S
C devices
P
2
C