MCP4021T-502E/SN Microchip Technology, MCP4021T-502E/SN Datasheet - Page 2

• Manufacturer Part Number: MCP4021T-502E/SN
• Description: IC DGTL POT 5K 1CH 8SOIC
• Manufacturer: Microchip Technology

Specifications of MCP4021T-502E/SN

• Memory Type: Non-Volatile
• Taps: 64
• Resistance (ohms): 5K
• Number Of Circuits: 1
• Temperature Coefficient: 150 ppm/°C Typical
• Interface: Up/Down
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Resistance In Ohms: 5K
• End To End Resistance: 5kohm
• Resistance Tolerance: ± 20%
• No. Of Steps: 64
• Supply Voltage Range: 2.7V To 5.5V
• Control Interface: 2 Wire, Serial
• No. Of Pots: Single
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCP4XXXDM-DB - BOARD DAUGHTER DIGIPOT MCP4XXXMCP402XEV - BOARD EVAL FOR MCP402X
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

MCP4021/2/3/4
1.0
Absolute Maximum Ratings †
V
CS and U/D inputs w.r.t V
A, B and W terminals w.r.t V
Current at Input Pins ..................................................±10 mA
Current at Supply Pins ...............................................±10 mA
Current at Potentiometer Pins ...................................±2.5 mA
Storage temperature .....................................-65°C to +150°C
Ambient temp. with power applied ................-55°C to +125°C
ESD protection on all pins
Maximum Junction Temperature (T
AC/DC CHARACTERISTICS
DS21945C-page 2
Electrical Specifications: Unless otherwise indicated, all parameters apply across the specified operating ranges.
T
T
Operating Voltage Range
CS Input Voltage
Supply Current
Resistance
(± 20%)
Resolution
Step Resistance
Note 1:
DD
A
A
= -40°C to +125°C, 2.1 k
= +25°C.
.............................................................................................................
2:
3:
4:
5:
6:
7:
8:
ELECTRICAL
CHARACTERISTICS
Resistance is defined as the resistance between terminal A to terminal B.
INL and DNL are measured at V
MCP4021/23 only, test conditions are: I
MCP4022/24 only, test conditions are:
Resistor terminals A, W and B’s polarity with respect to each other is not restricted.
This specification by design
Non-linearity is affected by wiper resistance (R
Section 6.0 “Resistor”
The MCP4021 is externally connected to match the configurations of the MCP4022 and MCP4024, and then tested.
Parameters
Resistance
Device
2.1 k
10 k
50 k
5 k
SS....................................
SS....................
2.25 mA
1.4 mA
450 μA
5 k
90 μA
5.5V
Current at Voltage
J
4 kV (HBM),
) . .........................+150°C
10 k and 50 k devices Typical specifications represent values for V
for additional information.
-0.3V to V
Sym
V
V
R
I
R
DD
N
DD
CS
AB
W
S
1.1 mA
450 μA
210 μA
-0.3V to 12.5V
40 μA
2.7V
with V
400V (MM)
DD
W
A
+ 0.3V
1.68
40.0
Min
V
= 1.9 mA, code = 00h.
2.7
4.0
8.0
= V
—
—
—
—
—
SS
6.5V
DD
MCP4022 includes V
MCP4024 includes V
W
), which changes significantly over voltage and temperature. See
and V
R
AB
Typ
0.3
0.6
2.1
45
15
10
50
—
—
5
64
/ 63
B
= V
Comments
† Notice: Stresses above those listed under “Maximum
Ratings” may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied.
Exposure to maximum rating conditions for extended periods
may affect device reliability.
SS
. (-202 devices V
Max
12.5
2.52
12.0
60.0
5.5
6.0
—
—
—
1
3
WZSE
WFSE
Units
Taps
mA
μA
μA
μA
k
k
k
k
V
V
A
= 4V).
The CS pin will be at one of three
input levels (V
(Note 6)
5.5V, CS = V
2.7V, CS = V
Serial Interface Inactive
(CS = V
T
-202 devices (Note 1)
-502 devices (Note 1)
-103 devices (Note 1)
-503 devices (Note 1)
No Missing Codes
Note 6
© 2005 Microchip Technology Inc.
A
= +25°C
IH
, U/D = V
DD
Conditions
SS
SS
= 5.5V, V
IL
, f
, f
, V
U/D
U/D
IH
IH
or V
= 1 MHz
= 1 MHz
)
SS
IHH
= 0V,
).