X93154UM8IZ-3T1 Intersil, X93154UM8IZ-3T1 Datasheet
![IC POT DGTL LP LN 50K OHM 8-MSOP](/photos/6/65/66540/20-8-msop_sml.jpg)
X93154UM8IZ-3T1
Specifications of X93154UM8IZ-3T1
Available stocks
Related parts for X93154UM8IZ-3T1
X93154UM8IZ-3T1 Summary of contents
Page 1
... CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. | 1-888-INTERSIL or 1-888-468-3774 Intersil (and design registered trademark of Intersil Americas Inc. XDCP is a trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2004, 2005, 2008. All Rights Reserved All other trademarks mentioned are the property of their respective owners. X93154 FN8180.3 CC Ω ...
Page 2
... Ordering Information PART NUMBER PART MARKING X93154UM8I-3* AGK X93154UM8IZ-3* (Note) AIW X93154UU8IZ-3* (Note) AKH *Add "T1" suffix for tape and reel. Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations ...
Page 3
... X93154 Thermal Information Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Temperature Under Bias . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp -[V H(n+1) must not decrease by more than 150mV from its initial value. CC Over recommended operating conditions unless otherwise stated. TEST CONDITIONS/NOTES = 50kΩ ...
Page 4
DC Electrical Specifications Over recommended operating conditions, unless otherwise specified. (Continued) SYMBOL PARAMETER INC, U/D Input Leakage Current LI V CS, INC, U/D Input HIGH Voltage IH V CS, INC, U/D Input LOW ...
Page 5
AC Timing INC U/D Power-Up and Power-down Requirements There are no restrictions on the power-up or power-down conditions of V and the voltages applied to the CC potentiometer pins provided that V CC positive than ...
Page 6
Instructions and Programming The INC, U/D and CS inputs control the movement of the wiper along the resistor array. With CS set LOW, the device is selected and enabled to respond to the U/D and INC inputs. HIGH to LOW ...
Page 7
Low Voltage High Impedance Instrumentation Amplifier 10k + V IN 10k - Micro-Power LCD Contrast Control 3.3V 240k 3.3V + 100k U1A - 100k 50k X93154 (R Single Supply Variable Gain Amplifier 7 X93154 3.3V + 10k U1A - 50k ...
Page 8
... The pin #1 identifier may be either a mold or mark feature Dimensions D2 and E2 are for the exposed pads which provide 0. improved electrical and thermal performance. 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389 TERMINAL TIP e MILLIMETERS MIN NOMINAL MAX A ...
Page 9
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...