X9313WSZ Intersil, X9313WSZ Datasheet - Page 3

• Manufacturer Part Number: X9313WSZ
• Description: IC XDCP 32-TAP 10K 3-WIRE 8-SOIC
• Manufacturer: Intersil
• Series: XDCP™r

Specifications of X9313WSZ

• Taps: 32
• Resistance (ohms): 10K
• Number Of Circuits: 1
• Temperature Coefficient: 300 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: Up/Down (3-Wire)
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Resistance In Ohms: 10K
• Track Taper: Linear
• Resistance Tolerance: ± 20%
• No. Of Steps: 32
• Supply Voltage Range: 4.5V To 5.5V
• Control Interface: 3 Wire, Serial
• No. Of Pots: Single
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Ordering Information
NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100%
matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
*Add “T1” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
**Add "T2" suffix for tape and reel. Please refer to TB347 for details on reel specifications.
***Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications.
Pin Descriptions
RH/VH and RL/VL
The high (RH/VH) and low (RL/VL) terminals of the X9313
are equivalent to the fixed terminals of a mechanical
potentiometer. The terminology of RL/VL and RH/VH
references the relative position of the terminal in relation to
wiper movement direction selected by the U/D input and not
the voltage potential on the terminal.
RW/VW
RW/VW is the wiper terminal and is equivalent to the
movable terminal of a mechanical potentiometer. The
position of the wiper within the array is determined by the
control inputs. The wiper terminal series resistance is
typically 40Ω at V
Up/Down (U/D)
The U/D input controls the direction of the wiper movement
and whether the counter is incremented or decremented.
Increment (INC)
The INC input is negative-edge triggered. Toggling INC will
move the wiper and either increment or decrement the
counter in the direction indicated by the logic level on the
U/D input.
X9313WS-3*
X9313WSZ-3* (Note)
X9313ZM-3*
X9313ZMZ-3* (Note)
X9313ZMI-3*
X9313ZMIZ-3* (Note)
X9313ZP-3
X9313ZPZ-3 (Note)
X9313ZS-3*
X9313ZSZ-3* (Note)
X9313ZSI-3*
X9313ZSIZ-3* (Note)
PART NUMBER
,
,
**
**
CC
= 5V.
X9313W D
X9313W ZD
13ZD
DDK
13ZE
13ZEZ
X9313ZP D
X9313ZP ZD
X9313Z D
X9313Z ZD
X9313Z E
X9313Z ZE
MARKING
PART
3
(Continued)
V
CC
3 to 5.5
RANGE
(V)
X9313
R
TOTAL
(kΩ)
10
1
Chip Select (CS)
The device is selected when the CS input is LOW. The current
counter value is stored in nonvolatile memory when CS is
returned HIGH while the INC input is also HIGH. After the
store operation is complete, the X9313 will be placed in the
low power standby mode until the device is selected once
again.
Pinouts
TEMPERATURE
-40 to +85
-40 to +85
-40 to +85
-40 to +85
RANGE
0 to +70
0 to +70
0 to +70
0 to +70
0 to +70
0 to +70
0 to +70
0 to +70
RW/VW
RH/VH
(°C)
RH/VH
RL/VL
VSS
INC
U/D
VSS
(8 LD PDIP, 8 LD SOIC)
1
2
3
4
1
2
3
4
(8 LD MSOP)
TOP VIEW
TOP VIEW
8 Ld SOIC
8 Ld SOIC (Pb-free)
8 Ld MSOP
8 Ld MSOP (Pb-free)
8 Ld MSOP
8 Ld MSOP (Pb-free)
8 Ld PDIP
8 Ld PDIP (Pb-free)***
8 Ld SOIC
8 Ld SOIC (Pb-free)
8 Ld SOIC
8 Ld SOIC (Pb-free)
X9313
X9313
X9313
X9313
PACKAGE
8
7
6
5
8
7
6
5
VCC
CS
RL/VL
RW/VW
U/D
INC
VCC
CS
January 15, 2008
MDP0027
M8.15
M8.118
M8.118
M8.118
M8.118
MDP0031
MDP0031
MDP0027
M8.15
MDP0027
M8.15
DWG. #
PKG.
FN8177.6