121LHS15 Renesas Electronics America, 121LHS15 Datasheet
121LHS15
Specifications of 121LHS15
Related parts for 121LHS15
121LHS15 Summary of contents
Page 1
High luminance, wide viewing angle, reversible scan direction DESCRIPTION The NL8060BC31- TFT (thin film transistor) active-matrix color liquid crystal display (LCD) module comprising an amorphous silicon TFT attached to each signal electrode, a ...
Page 2
... L 6-bit signals for each of RGB primary colors, synchronous signals (Hsync, Vsync), dot clock (CLK) 3.3 V [5.0 V] (logic, LCD driving) Edge light type, two cold cathode fluorescent lamps in a holder Lamp holder: Part No.121LHS15 Recommended inverter: Part no. 121PW111 7.0 W (typ rms/lamp) L Data Sheet EN0510EJ1V1DS00 ...
Page 3
BLOCK DIAGRAM 200 R0 R5 200 G0 G5 200 CLK 200 H sync 200 V sync 200 DE DPS 4 GND DC/DC Converter V HIGH V HIGH V LOW Note: GND is not connected ...
Page 4
GENERAL SPECIFICATIONS Item Module size Display area 246.0 (H) Number of pixels Dot pitch Pixel pitch Pixel arrangement Display colors Weight ABSOLUTE MAXIMUM RATINGS Parameter Symbol Supply voltage V CC Input voltage V I Lamp voltage V L Storage temp. ...
Page 5
Backlight Parameter Symbol Lamp current I L Lamp voltage V L Lamp turn-on voltage V S Note 2 Oscillator frequency Ft Notes atmosphere of below 10 C, keep the lamp current more than 3.0 mA rms ...
Page 6
INTERFACE AND CONNECTOR PIN ASSIGNMENT (1) Interface Signals, Power Supply CN1: DF9-41P-1V (Hirose Electric Co., Ltd.) Adaptable socket: DF9-41S-1V (Hirose Electric Co., Ltd.) or IL-310-T41S-VF (Japan Aviation Electronics Industry, Limited (JAE)) Pin No. Symbol Function 1 GND Ground 2 CLK ...
Page 7
Lamp Connector CN2: BHR-03VS-1 Adaptable socket: SM03 (4.0) B-BHS-TB Supplier: J.S.T. Trading Company, Ltd. Pin No. Symbol Function 1 V Low-voltage terminal LOW 2 V High-voltage terminal HIGH 3 V High-voltage terminal HIGH Caution: V and V must be ...
Page 8
Luminance control using a variable resistor This method works when BRTHL (No.5 pin) of CN1 is opened. BRTL <2> Luminance control by voltage BRTL and BRTHL are opened. The input voltage range between BRTH and GNDB is as ...
Page 9
Connector Location CN2 CN1 CN3 Recommended inverter (121PW111 <Lamp side pin arrangement of CN2> <Inverter side pin arrangement of CN3> Upper side <Rear view> Lower side <Inverter side pin arrangement of CN1> Data ...
Page 10
DISPLAY COLORS vs. INPUT DATA SIGNALS Display Colors R5 R4 Black 0 0 Blue 0 0 Red 1 1 Magenta 1 1 Basic colors Green 0 0 Cyan 0 0 Yellow 1 1 White 1 1 Black ...
Page 11
INPUT SIGNAL TIMING (1) Input Signal Specifications Parameter CLK Frequency Duty Rise, fall Hsync Period Display period Front porch Pulse width Back porch thp + thb CLK-Hsync timing Hsync-CLK timing Hsync-Vsync timing Vsync-Hsync timing Rise, fall Vsync Period Display period ...
Page 12
Definition of Input Signal Timing <Vertical> Vsync Display period (Note) DE <Horizontal> Hsync Display period (Note tvp tvb tvd th thp thb thd Note: These do not exist as signals. Data Sheet EN0510EJ1V1DS00 NL8060BC31-17 tvf thf ...
Page 13
C tch 0 0.5 V CLK CC 0 tcrf DATA Invalid (R0 R5) 0 (G0 G5) 0 (B0 B5 0.3 V ...
Page 14
Input Signal Timing Chart a) Fixed timing mode Vsync 1 H (min (min (fixed) Hsync Hsync (X, 0) Invalid Hsync R0 ...
Page 15
DE mode Vsync tvp tvb Hsync ( (X, Y) Invalid ( (1, Y) Invalid Hsync thp ...
Page 16
DISPLAY POSITION Normal scan (DPS = “Low” or “Open” (0, 598) D (1, 598) D (0, 599) D (1, 599) Reverse ...
Page 17
OPTICAL CHARACTERISTICS Item Symbol Note 2 Contrast ratio CR Luminance Lumax Note 2 Luminance uniformity max./min. Reference data Item Symbol Color gamut C at center, to NTSC Horizontal x+ CR > 10 Viewing angle range x CR ...
Page 18
The luminance uniformity is calculated by using the following formula. Maximum luminance Luminance uniformity = Minimum luminance The luminance is measured at or near the five points shown below. Column 6. The definition of response time is as follows. ...
Page 19
RELIABILITY TEST SPECIFICATIONS Test Items High temperature/humidity 85% relative humidity operation 240 hours Display data is black. Heat cycle (operation) <1> <2> 50 cycles, 4 hours/cycle <3> Display data ...
Page 20
GENERAL CAUTIONS The figures and statements below are very important. Please be sure you understand their contents. This figure is a mark that you will get hurt and/or the module will be damaged if you make a CAUTION mistake in ...
Page 21
Cautions regarding module characteristics <1> Do not apply fixed-pattern data for a long time to the LCD module. It may cause image sticking. Please use screen savers if the display pattern is fixed for a long time. <2> This ...
Page 22
OUTLINE DRAWING FRONT SIDE (Unit: mm) 13.7 MAX. (3.3) 2.5 0.3 (4.5) ACTIVE AREA (246 184.5) (4.5) 2.5 0 3.5) (3.3) 13.7 MAX. Notes: 1. The values in parentheses are for reference. 2. The torque on a mounting ...
Page 23
OUTLINE DRAWING REAR SIDE (Unit: mm) (5) HIOK VOLTAGE CAUTION CN2 S THE TFT COLOR LCD PANEL CONTAINS COLD CATHODE FLUORESCENT LAMPS. PLEASE FOLLOW LOCAL ORDINANCES OR REGULATIONS FOR THEIR DISPOSAL. (5.0) Notes: 1. The value in parentheses are for ...
Page 24
...