BTS409L1-E3043 Infineon Technologies, BTS409L1-E3043 Datasheet
BTS409L1-E3043
Specifications of BTS409L1-E3043
Related parts for BTS409L1-E3043
BTS409L1-E3043 Summary of contents
Page 1
... Standard Gate Overvoltag Curren limit protectio protectio Limit for Charge unclampe Level ind. f Rectifier Open Short to detectio GND 1 Signal GND =150 ) in GND connection, resistor in series with ST GND 1 BTS409L1 V bb(AZ) V 5.0 ... 34 V bb(on L(ISO) I L(SCr) TO-220AB Straight leads + OUT 5 Temperatur sensor Load ...
Page 2
... Symbol chip - case: R thJC R thJA 5) : require an external current limit for the GND and status pins, e.g. with a bb(AZ) resistor in series with the status pin. A resistor for the 2 (one layer thick) copper area for BTS409L1 Symbol Values Load dump I self-limited L T -40 ...
Page 3
... V j bb(o rst) T =-40...+150° =-40...+150° bb(AZ =-40...+25° bb(off 150° L(off) bb(off GND = 5.6 V typ without charge pump BTS409L1 Values min typ max -- 160 200 320 400 1.8 2 200 400 80 200 400 0 0.1 -- off 5.0 -- 3 ...
Page 4
... External pull up resistor required for open load detection in off state. Infineon Technologies AG Symbol I L(SCp) T =-40° =25° =+150° L(SCr mA ON(CL =-40 ° (OL) T =25 ..150° (off-condition OUT(OL) T =-40..150° >5 BTS409L1 Values Unit min typ max 5.5 9 4.5 7 150 -- -- ° 200 150 ...
Page 5
... Infineon Technologies AG Symbol ) =-40..+150° IN(T+) T =-40..+150° IN(T-) V IN( IN(off IN(on) t d(ST OL4) =-40..+150° d(ST =-40 ... +150°C: = +1.6 mA ST(high) = +1.6 mA ST(low) = +1.6 mA BTS409L1 Values Unit min typ max 2.5 3 1.7 -- 3 100 400 800 s -- 250 600 s 5.4 6 ...
Page 6
... V ON OUT 5 ESD zener diodes are not to be used as voltage clamp V OUT at DC conditions. Operation in this mode may result in a drift of the zener voltage (increase V the off state, causes an internal current from output to ground BTS409L1 ESD- GND signal may be errorious. ST low ...
Page 7
... OFF-state diagnostic condition OUT Logic unit GND disconnect + PROFET GND Signal GND = 150 , GND Any kind of load. In case of Input=high is V Due to V > GND 7 BTS409L1 < L(OL OUT Open load detection > typ.; IN low OUT R EXT OFF V Open load R detection O Signal GND OUT ...
Page 8
... Inductive Load switch-off energy dissipation E bb OUT 5 = Energy stored in load inductance: While demagnetizing load inductance, the energy dissipated in PROFET OUT 5 with an approximate solution for Maximum allowable load inductance for a single switch off [mH] 10000 1000 D 100 BTS409L1 OUT PROFET ST GND · · · (t) dt ON(CL · ...
Page 9
... Transient thermal impedance chip case Z = f(t )Z [K/W] thJC p thJC 10 1 0.1 0.01 1E-5 1E-4 1E-3 1E-2 1E-1 Infineon Technologies AG D= 0.5 0.2 0.1 0.05 0.02 0.01 0 1E0 1E1 1E2 t p [s] 9 BTS409L1 2003-Oct-01 ...
Page 10
... I L Infineon Technologies AG Figure 2b: Switching an inductive load IN t d(ST OUT L(OL the time constant of load is too large, open-load-status may occur Figure 3a: Short circuit shut down by overtempertature, reset by cooling L(SCp) I L(SCr Heating up may require several milliseconds, depending on external conditions 10 BTS409L1 t t 2003-Oct-01 ...
Page 11
... Figure 5b: Open load: detection in ON-state, open load occurs in on-state IN t d(ST OL1 OUT normal typ., t d(ST OL1) Figure 5c: Open load: detection in ON- and OFF-state (with R ), turn on/off to open load EXT IN t d(ST OL4 OUT BTS409L1 t d(ST OL2) normal open typ d(ST OL2) t d(ST) open t 2003-Oct-01 ...
Page 12
... V bb(under) V OUT ST open drain Figure 6b: Undervoltage restart of charge pump bb(over bb(o rst) bb(u rst) V bb(u cp) V bb(under) charge pump starts at V =5.6 V typ. bb(ucp) Infineon Technologies AG Figure 7a: Overvoltage bb(u cp) V bb(u rst) V OUT ON(CL BTS409L1 bb(over) bb(o rst) ON(CL) 2003-Oct-01 t ...
Page 13
... Package and Ordering Code All dimensions in mm Standard TO-220AB/5 BTS409L1 TO-220AB/5, Option E3043 BTS409L1 E3043 Infineon Technologies AG SMD TO-220AB/5, Opt. E3062 Ordering code Q67060-S6107-A2 BTS409L1 E3062A T&R: Changed since 04.96 Date Dec 1996 Ordering code Q67060-S6107-A3 2000 13 BTS409L1 Ordering code Q67060-S6107-A4 ...
Page 14
... Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life. If they fail reasonable to assume that the health of the user or other persons may be endangered. Infineon Technologies AG 14 BTS409L1 2003-Oct-01 ...