BTS308-E3062A Infineon Technologies, BTS308-E3062A Datasheet
BTS308-E3062A
Specifications of BTS308-E3062A
Related parts for BTS308-E3062A
BTS308-E3062A Summary of contents
Page 1
... Loss of ground and loss of V protection bb Electrostatic discharge (ESD) protection Application C compatible power switch with diagnostic feedback for 12 V and grounded loads Most suitable for inductive loads Replaces electromechanical relays, fuses and discrete circuits Fast switching Not suitable for lamp loads ...
Page 2
... Current through status pin (DC) see internal circuit diagrams page 6 Thermal resistance Semiconductor Group Function Logic ground Input, activates the power switch in case of logical high signal Positive power supply voltage, the tab is shorted to this pin Diagnostic feedback, low on failure Output to the load 25 °C ...
Page 3
... Electrical Characteristics Parameter and Conditions ° unless otherwise specified j bb Load Switching Capabilities and Characteristics On-state resistance (pin 0 12V Nominal load current, ISO Norm (pin 0 ° Output current (pin ) while GND disconnected or 5 GND pulled up page 7 Turn-on time to 90 OUT ...
Page 4
... V ON ON(SC 12V bb Short circuit shutdown delay after input pos. slope V > ON(SC) min value valid only, if input "low" time exceeds 60 s Output clamp (inductive load switch off OUT bb ON(CL) Short circuit shutdown detection voltage (pin Thermal overload trip temperature Thermal hysteresis ...
Page 5
Parameter and Conditions ° unless otherwise specified j bb Input and Status Feedback Input resistance see circuit page 6 Input turn-on threshold voltage Input turn-off threshold voltage Input threshold hysteresis, T Off ...
Page 6
Truth Table Input- Output level level Normal L L operation Open load Short circuit GND H L Short circuit Overtem perature ...
Page 7
Inductive and overvoltage output clamp V Z PROFET GND V clamped typ. ON Overvolt. and reverse batt. protection Logic GND V = 6.2 V typ., V ...
Page 8
... high OUT PROFET GND other external inductive loads L are connected to the PROFET, additional elements like D are necessary. Semiconductor Group Inductive Load switch-off energy dissipation PROFET = ST GND Energy stored in load inductance While demagnetizing load inductance, the energy dissipated in PROFET ...
Page 9
... Options Overview all versions: High-side switch, Input protection, ESD protection, load dump and reverse battery protection with 150 Type Logic version Overtemperature protection with hysteresis >150 °C, latch function ) T j >150 °C, with auto-restart on cooling Short circuit to GND protection switches off when V > ...
Page 10
... Figure 1a: V turn on d(bb IN OUT A ST open drain A in case of too early V IN =high the device may not turn on (curve A) t approx. 150 s d(bb IN) Figure 2a: Switching an inductive load OUT I L Semiconductor Group Figure 3a: Turn on into short circuit OUT t d(SC d(SC) approx. 200 ...
Page 11
Figure 3c: Short circuit while on OUT I L **) **) current peak approx Figure 4a: Overtemperature, Reset if (IN=low) and (T < OUT goes ...
Page 12
Figure 6b: Undervoltage restart of charge pump bb(o rst) bb(u rst) V bb(u cp) V bb(under) charge pump starts at V =4.9 V typ. bb(ucp) Figure 7a: Overvoltage ON(CL) bb(over) bb ...
Page 13
Package and Ordering Code All dimensions in mm Standard TO-220AB/5 BTS 308 TO-220AB/5, Option E3043 BTS 308 E3043 Semiconductor Group SMD TO-220AB/5, Opt. E3062 Ordering code BTS 308 E3062A tbd Ordering code tbd Page 13 BTS 308 Ordering code T&R: ...
Page 14
... ON Option overview, Short circuit to GND protection, " " deletet for V > typ bb BTS308, only valid for BTS410H2 Published by Infineon Technologies AG, St.-Martin-Strasse 53, D-81669 München © Infineon Technologies AG 2001 All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics ...