DS90CR484AVJD National Semiconductor, DS90CR484AVJD Datasheet - Page 6
![](/photos/31/30/313088/100pin_tqfp_sml.jpg)
DS90CR484AVJD
Manufacturer Part Number
DS90CR484AVJD
Description
Manufacturer
National Semiconductor
Datasheet
1.DS90CR484AVJD.pdf
(24 pages)
Specifications of DS90CR484AVJD
Number Of Elements
8
Number Of Receivers
8
Number Of Drivers
48
Input Type
CMOS/TTL
Operating Supply Voltage (typ)
3.3V
Differential Input High Threshold Voltage
100mV
Diff. Input Low Threshold Volt
-100mV
Output Type
Deserializer
Differential Output Voltage
450mV
Power Dissipation
2.3W
Operating Temp Range
-10C to 70C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
100
Package Type
TQFP
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS90CR484AVJD/NOPB
Manufacturer:
NSC
Quantity:
90
Company:
Part Number:
DS90CR484AVJD/NOPB
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
DS90CR484AVJDX/NOPB
Manufacturer:
Texas Instruments
Quantity:
10 000
www.national.com
RSKM
RSKM
RSKMD
RDR
RDSS
Symbol
Chipset RSKM Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.(Notes 4, 7). See Applications Informa-
tion section for more details on this parameter and how to apply it.
Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device
should be operated at these limits. The tables of “Electrical Characteristics” specify conditions for device operation.
Note 2: Typical values are given for V
Note 3: Current into device pins is defined as positive. Current out of device pins is defined as negative. Voltages are referenced to ground unless otherwise
specified (except V
Note 4: The Minimum and Maximum Limits are based on statistical analysis of the device performance over voltage and temperature ranges. This parameter is
functionally tested on Automatic Test Equipment (ATE). ATE is limited to 85MHz. A sample of characterization parts have been bench tested to verify functional
performance.
Note 5: Receiver Skew Margin (RSKM) is defined as the valid data sampling region at the receiver inputs. This margin takes into account transmitter output pulse
positions (min and max) and the receiver input setup and hold time (internal data sampling window - RSPOS). This margin allows for LVDS interconnect skew,
inter-symbol interference (both dependent on type/length of cable) and clock jitter.
RSKM
Note 6: Receiver Skew Margin with Deskew (RSKMD) is defined as the valid data sampling region at the receiver inputs. The DESKEW function will constrain
the receiver’s sampling strobes to the middle half of the LVDS bit and removes (adjusts for) fixed interconnect skew. This margin (RSKMD) allows for inter-symbol
interference (dependent on type/length of cable), Transmitter Pulse Position (TPPOS) variance, and LVDS clock jitter (TJCC).
RSKMD
Note 7: Typical values for RSKM and RSKMD are applicable for fixed V
and T
Note 8: TJCC is a function of input clock quality and also PLLVCC noise. At 112MHz operation, with a +/−300ps input impulse at a 2us rate, TJCC has been
measured to be in the 70-80ps range (<100ps). With a nominal input clock quality (no input impulse jitter, jitter < 500kHz), TJCC is typically 50ps or less. For
RSKM/RSKMD calculations 100ps is typically used as the TJCC budget. See Clock Jitter discussion in the Applications Information section of this datasheet for
further information.
A
≥
points).
≥
cable skew (type, length) + source clock jitter (cycle to cycle, TJCC) + ISI (if any). See Applications Information section for more details.
ISI + TPPOS(variance) + source clock jitter (cycle to cycle). See Applications Information section for more details.
Receiver Skew Margin without Deskew
in non-DC Balance Mode, (Figure 13),
(Note 5)
Receiver Skew Margin without Deskew
in DC Balance Mode, (Figure 13),
(Note 5)
Receiver Skew Margin with Deskew in
DC Balance, (Figure 14),
(Note 6)
Receiver Deskew Range
Receiver Deskew Step Size
TH
, V
TL
, V
OD
and ΔV
CC
OD
Parameter
= 3.3V and T
).
A
= +25°C.
f = 112 MHz
f = 100 MHz
f = 85MHz
f = 66MHz
f = 112 MHz
f = 100 MHz
f = 85 MHz
f = 66 MHz
f = 50MHz
f = 33 to 80 MHz
f = 80 MHz
f = 80 MHz
CC
and T
6
A
for the Transmitter and Receiver (both are assumed to be at the same V
0.25TBIT
Min
170
170
300
300
170
170
250
250
300
±1
0.3TBIT
Typ
240
350
350
200
300
300
350
Max
Units
TBIT
CC
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ns