AD5382BST-5 Analog Devices Inc, AD5382BST-5 Datasheet - Page 30

no-image

AD5382BST-5

Manufacturer Part Number
AD5382BST-5
Description
IC DAC 14BIT 32CH 5V 100-LQFP
Manufacturer
Analog Devices Inc
Datasheet

Specifications of AD5382BST-5

Design Resources
32 Channels of Programmable Voltage with Excellent Temperature Drift Performance Using AD5382 (CN0011) AD5382 Channel Monitor Function (CN0012)
Settling Time
8µs
Number Of Bits
14
Data Interface
Serial, Parallel
Number Of Converters
32
Voltage Supply Source
Single Supply
Power Dissipation (max)
65mW
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
100-LQFP
For Use With
EVAL-AD5382EB - BOARD EVAL FOR AD5382
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
AD5382
2-Byte Mode
Following initialization of 2-byte mode, the user can update
channels sequentially. The device address byte is required only
once, and the pointer address pointer is configured for auto-
increment or burst mode.
The user must begin with an address byte (R/ W = 0), after
which the DAC acknowledges that it is prepared to receive data
by pulling SDA low. The address byte is followed by a specific
pointer byte (0xFF) that initiates the burst mode of operation.
The address pointer initializes to Channel 0, the data following
the pointer is loaded to Channel 0, and the address pointer
automatically increments to the next address.
The REG0 and REG1 bits in the data byte determine which
register is updated. In this mode, following the initialization,
only the two data bytes are required to update a channel. The
channel address automatically increments from Address 0 to
Channel 31 and then returns to the normal 3-byte mode of
operation. This mode allows transmission of data to all channels
in one block and reduces the software overhead in configuring all
channels. A stop condition at any time exits this mode. Toggle
mode is not supported in 2-byte mode. Figure 33 shows a
typical configuration.
SDA
SDA
SDA
SDA
SCL
SCL
SCL
SCL
START COND
BY MASTER
REG1
REG1
1
REG1
REG0
REG0
0
MOST SIGNIFICANT DATA BYTE
MOST SIGNIFICANT DATA BYTE
REG0
MOST SIGNIFICANT DATA BYTE
ADDRESS BYTE
MSB
MSB
1
MSB
0
1
AD1
AD0
CHANNEL N DATA FOLLOWED BY STOP
Figure 33. 2-Byte, I
CONVERTER
LSB
LSB
ACK BY
R/W
CONVERTER
LSB
Rev. B | Page 30 of 40
ACK BY
ACK BY
AD538x
CHANNEL 0 DATA
CHANNEL 1 DATA
CONVERTER
ACK BY
A7 = 1 A6 = 1 A5 = 1 A4 = 1 A3 = 1 A2 = 1 A1 = 1 A0 = 1
MSB
MSB
MSB
2
C Write Operation
MSB
PARALLEL INTERFACE
The SER/ PAR pin must be tied low to enable the parallel
interface and disable the serial interfaces.
timing diagram for a parallel write. The parallel interface is
controlled by the following pins.
CS Pin
Active low device select pin.
WR Pin
On the rising edge of WR , with CS low, the addresses on Pins
A4 to A0 are latched; data present on the data bus is loaded into
the selected input registers.
REG0, REG1 Pins
The REG0 and REG1 pins determine the destination register of
the data being written to the AD5382. See Table 11.
Pins A4 to A0
Each of the 40 DAC channels can be addressed individually.
Pins DB13 to DB0
The AD5382 accepts a straight 14-bit parallel word on DB13 to
DB0, where DB13 is the MSB and DB0 is the LSB.
LEAST SIGNIFICANT DATA BYTE
LEAST SIGNIFICANT DATA BYTE
LEAST SIGNIFICANT DATA BYTE
POINTER BYTE
CONVERTER
LSB
LSB
CONVERTER
ACK BY
ACK BY
AD538x
ACK BY
Figure 7
CONVERTER
LSB
ACK BY
shows the
MASTER
COND
STOP
BY

Related parts for AD5382BST-5