EPM570F100C4N Altera, EPM570F100C4N Datasheet - Page 53

• Manufacturer Part Number: EPM570F100C4N
• Description: IC MAX II CPLD 570 LE 100-FBGA
• Manufacturer: Altera
• Series: MAX® IIr

Specifications of EPM570F100C4N

• Programmable Type: In System Programmable
• Delay Time Tpd(1) Max: 5.4ns
• Voltage Supply - Internal: 2.5V, 3.3V
• Number Of Logic Elements/blocks: 570
• Number Of Macrocells: 440
• Number Of I /o: 76
• Operating Temperature: 0°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 100-FBGA
• Voltage: 2.5V, 3.3V
• Memory Type: FLASH
• Number Of Logic Elements/cells: 570
• Family Name: MAX II
• # Macrocells: 440
• Frequency (max): 2.3148GHz
• Propagation Delay Time: 7ns
• Number Of Logic Blocks/elements: 57
• # I/os (max): 76
• Operating Supply Voltage (typ): 2.5/3.3V
• In System Programmable: Yes
• Operating Supply Voltage (min): 2.375V
• Operating Supply Voltage (max): 3.6V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: FBGA
• No. Of I/o's: 76
• Propagation Delay: 7ns
• Global Clock Setup Time: 1.5ns
• Frequency: 247.5MHz
• Supply Voltage Range: 2.375V To 2.625V, 3V To 3.6V
• Operating Temperature Range: 0°C To +85°C
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 544-1716

Chapter 4: Hot Socketing and Power-On Reset in MAX II Devices
Hot Socketing Feature Implementation in MAX II Devices
Figure 4–1. Hot Socketing Circuit Block Diagram for MAX II Devices
© October 2008 Altera Corporation
f
1
Make sure that the V
SRAM download has completed.
Each I/O and clock pin has the circuitry shown in
The POR circuit monitors V
until the device has completed its flash memory configuration of the SRAM logic. The
weak pull-up resistor (R) from the I/O pin to V
keep the I/O pins from floating. The 3.3-V tolerance control circuit permits the I/O
pins to be driven by 3.3 V before V
I/O pins from driving out when the device is not fully powered or operational. The
hot socket circuit prevents I/O pins from internally powering V
driven by external signals before the device is powered.
For information about 5.0-V tolerance, refer to the
Voltage Systems
Figure 4–2
This design ensures that the output buffers do not drive when V
V
voltage spikes during hot insertion. The V
tolerant circuit capacitance.
Resistor
Pull-Up
CCINT
Weak
PAD
or if the I/O pad voltage is higher than V
shows a transistor-level cross section of the MAX II device I/O buffers.
chapter in the MAX II Device Handbook.
V
CCINT
CCIO
is within the recommended operating range even though
CCINT
and V
Input Buffer
to Logic Array
CCIO
Tolerance
Voltage
Control
CCIO
and/or V
voltage levels and keeps I/O pins tri-stated
PAD
Output Enable
leakage current charges the 3.3-V
CCIO
CCIO
CCINT
Using MAX II Devices in Multi-
Figure
. This also applies for sudden
is enabled during download to
Hot Socket
are powered, and it prevents the
Power On
Monitor
Reset
4–1.
CCIO
CCIO
is powered before
and V
MAX II Device Handbook
CCINT
when
4–3