EP2S60F1020I4 Altera, EP2S60F1020I4 Datasheet - Page 120

• Manufacturer Part Number: EP2S60F1020I4
• Description: IC STRATIX II FPGA 60K 1020-FBGA
• Manufacturer: Altera
• Series: Stratix® IIr

Specifications of EP2S60F1020I4

• Number Of Logic Elements/cells: 60440
• Number Of Labs/clbs: 3022
• Total Ram Bits: 2544192
• Number Of I /o: 718
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 1020-FBGA
• Family Name: Stratix II
• Number Of Logic Blocks/elements: 60440
• # I/os (max): 718
• Frequency (max): 711.24MHz
• Process Technology: 90nm (CMOS)
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 60440
• Ram Bits: 2544192
• Operating Supply Voltage (min): 1.15V
• Operating Supply Voltage (max): 1.25V
• Operating Temp Range: -40C to 100C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 1020
• Package Type: FC-FBGA
• For Use With: 544-1700 - DSP KIT W/STRATIX II EP2S60N544-1697 - NIOS II KIT W/STRATIX II EP2S60N
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Not Compliant
• Other names: 544-1903; EP2S60F1020I4

Configuration
3–6
Stratix II Device Handbook, Volume 1
The PLL_ENA pin and the configuration input pins
dual buffer design: a 3.3-V/2.5-V input buffer and a 1.8-V/1.5-V input
buffer. The VCCSEL input pin selects which input buffer is used. The 3.3-
V/2.5-V input buffer is powered by V
buffer is powered by V
VCCSEL is sampled during power-up. Therefore, the VCCSEL setting
cannot change on the fly or during a reconfiguration. The VCCSEL input
buffer is powered by V
A logic high VCCSEL connection selects the 1.8-V/1.5-V input buffer, and
a logic low selects the 3.3-V/2.5-V input buffer. VCCSEL should be set to
comply with the logic levels driven out of the configuration device or
MAX
If you need to support configuration input voltages of 3.3 V/2.5 V, you
should set the VCCSEL to a logic low; you can set the V
bank that contains the configuration inputs to any supported voltage. If
nSTATUS
used as an input)
nCONFIG
CONF_DONE
(when used as an
input)
DATA[7..0]
nCE
DCLK
as an input)
CS
nWS
nRS
nCS
CLKUSR
DEV_OE
DEV_CLRn
RUnLU
PLL_ENA
Table 3–4. Pins Affected by the Voltage Level at VCCSEL
®
(when used
II/microprocessor.
Pin
(when
3.3/2.5-V input buffer is
selected. Input buffer is
powered by V
VCCSEL = LOW (connected
CCIO
CCINT
.
Table 3–4
to GND)
and must be hardwired to V
C C P D
.
shows the pins affected by VCCSEL.
CCPD,
while the 1.8-V/1.5-V input
1.8/1.5-V input buffer is
selected. Input buffer is
powered by V
bank.
VCCSEL = HIGH (connected
(Table
Altera Corporation
CCIO
to V
CCPD
3–4) have a
C C I O
CCPD
of the I/O
or ground.
)
of the I/O
May 2007