XC4062XL-2BG560I Xilinx Inc, XC4062XL-2BG560I Datasheet - Page 50
![no-image](/images/no-image-200.jpg)
XC4062XL-2BG560I
Manufacturer Part Number
XC4062XL-2BG560I
Description
IC FPGA I-TEMP 3.3V 2SPD 560MBGA
Manufacturer
Xilinx Inc
Series
XC4000E/Xr
Datasheet
1.XC4005E-4PC84C.pdf
(68 pages)
Specifications of XC4062XL-2BG560I
Number Of Logic Elements/cells
5472
Number Of Labs/clbs
2304
Total Ram Bits
73728
Number Of I /o
384
Number Of Gates
62000
Voltage - Supply
3 V ~ 3.6 V
Mounting Type
Surface Mount
Operating Temperature
-40°C ~ 100°C
Package / Case
560-LBGA, Metal
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
XC4000E and XC4000X Series Field Programmable Gate Arrays
Start-up from a User Clock (STARTUP.CLK)
When, instead of CCLK, a user-supplied start-up clock is
selected, Q1 is used to bridge the unknown phase relation-
ship between CCLK and the user clock. This arbitration
causes an unavoidable one-cycle uncertainty in the timing
of the rest of the start-up sequence.
DONE Goes High to Signal End of Configuration
XC4000 Series devices read the expected length count
from the bitstream and store it in an internal register. The
length count varies according to the number of devices and
the composition of the daisy chain. Each device also counts
the number of CCLKs during configuration.
Two conditions have to be met in order for the DONE pin to
go high:
• the chip's internal memory must be full, and
• the configuration length count must be met, exactly .
This is important because the counter that determines
when the length count is met begins with the very first
CCLK, not the first one after the preamble.
Therefore, if a stray bit is inserted before the preamble, or
the data source is not ready at the time of the first CCLK,
the internal counter that holds the number of CCLKs will be
one ahead of the actual number of data bits read. At the
end of configuration, the configuration memory will be full,
but the number of bits in the internal counter will not match
the expected length count.
As a consequence, a Master mode device will continue to
send out CCLKs until the internal counter turns over to
zero, and then reaches the correct length count a second
time. This will take several seconds [2
which is sometimes interpreted as the device not configur-
ing at all.
If it is not possible to have the data ready at the time of the
first CCLK, the problem can be avoided by increasing the
number in the length count by the appropriate value. The
XACT User Guide includes detailed information about man-
ually altering the length count.
Note that DONE is an open-drain output and does not go
High unless an internal pull-up is activated or an external
pull-up is attached. The internal pull-up is activated as the
default by the bitstream generation software.
6-54
Product Obsolete or Under Obsolescence
24
CCLK period] —
Release of User I/O After DONE Goes High
By default, the user I/O are released one CCLK cycle after
the DONE pin goes High. If CCLK is not clocked after
DONE goes High, the outputs remain in their initial state —
3-stated, with a 50 k
DONE High to active user I/O is controlled by an option to
the bitstream generation software.
Release of Global Set/Reset After DONE Goes
High
By default, Global Set/Reset (GSR) is released two CCLK
cycles after the DONE pin goes High. If CCLK is not
clocked twice after DONE goes High, all flip-flops are held
in their initial set or reset state. The delay from DONE High
to GSR inactive is controlled by an option to the bitstream
generation software.
Configuration Complete After DONE Goes High
Three full CCLK cycles are required after the DONE pin
goes High, as shown in
not clocked three times after DONE goes High, readback
cannot be initiated and most boundary scan instructions
cannot be used.
Configuration Through the Boundary Scan
Pins
XC4000 Series devices can be configured through the
boundary scan pins. The basic procedure is as follows:
• Power up the FPGA with INIT held Low (or drive the
• Issue the CONFIG command to the TMS input
• Wait for INIT to go High
• Sequence the boundary scan Test Access Port to the
• Toggle TCK to clock data into TDI pin.
The user must account for all TCK clock cycles after INIT
goes High, as all of these cycles affect the Length Count
compare.
For more detailed information, refer to the Xilinx application
note XAPP017, “ Boundary Scan in XC4000 Devices .” This
application note also applies to XC4000E and XC4000X
devices.
PROGRAM pin Low for more than 300 ns followed by a
High while holding INIT Low). Holding INIT Low allows
enough time to issue the CONFIG command to the
FPGA. The pin can be used as I/O after configuration if
a resistor is used to hold INIT Low.
SHIFT-DR state
- 100 k
Figure 47 on page
May 14, 1999 (Version 1.6)
pull-up. The delay from
53. If CCLK is
R