20-101-0525 Rabbit Semiconductor, 20-101-0525 Datasheet - Page 133
20-101-0525
Manufacturer Part Number
20-101-0525
Description
COMPUTER SINGLE-BOARD LP3500 FOX
Manufacturer
Rabbit Semiconductor
Specifications of 20-101-0525
Module/board Type
Single Board Computer Module
Product
Modules
Processor Type
Rabbit 3000
Sram
512 KB
Flash
512 KB
Timers
8 bit, 10 bit
Number Of I/os
26
Backup Battery
3 V Lithium Coin Type
Operating Voltage
3 V to 30 V
Board Size
93 mm x 66 mm x 11 mm
Description/function
Computer Module
For Use With/related Products
LP3500
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
316-1115
- Current page: 133 of 142
- Download datasheet (4Mb)
E.2.3 Reset Generator
The LP3500 module uses a reset generator on the module, U11, to reset the Rabbit 3000
microprocessor when the voltage drops below the voltage necessary for reliable operation.
The reset occurs between 2.55 V and 2.75 V, typically 2.63 V.
E.3 Chip Select Circuit
The current drain on the battery in a battery-backed circuit must be kept at a minimum.
When the LP3500 is not powered, the battery keeps the SRAM memory contents and the
real-time clock (RTC) going. The SRAM has a powerdown mode that greatly reduces
power consumption. This powerdown mode is activated by raising the chip select (CS)
signal line. Normally the SRAM requires Vcc to operate. However, only 2 V is required
for data retention in powerdown mode. Thus, when power is removed from the circuit, the
battery voltage needs to be provided to both the SRAM power pin and to the CS signal
line. The CS control circuit accomplishes this task for the SRAM’s chip select signal line.
In a powered-up condition, the CS control circuit must allow the processor’s chip select
signal /CS1 to control the SRAM’s CS signal /CSRAM. So, with power applied, /CSRAM
must be the same signal as /CS1, and with power removed, /CSRAM must be held high
(but only needs to be battery voltage high).The isolated /CSRAM line has a 220 kΩ pullup
resistor to VRAM (R46). This pullup resistor keeps /CSRAM at the VRAM voltage level
(which under no power condition is the backup battery’s regulated voltage at a little more
than 2 V).
User’s Manual
127
Related parts for 20-101-0525
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: