20-101-0709 Rabbit Semiconductor, 20-101-0709 Datasheet - Page 30
20-101-0709
Manufacturer Part Number
20-101-0709
Description
INTERFACE GRAPHIC DISPLAY OP6700
Manufacturer
Rabbit Semiconductor
Datasheet
1.101-0412.pdf
(90 pages)
Specifications of 20-101-0709
Module/board Type
Single Board Computer Module
For Use With/related Products
OP6700
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
20-101-709
20-101-709
20-101-709
- Current page: 30 of 90
- Download datasheet (2Mb)
3.2.3 Programming Port
The Intellicom has a 10-pin programming header labeled J4. The programming port uses
the Rabbit 2000’s serial port A for communication. The programming port uses the Rabbit
2000’s Serial Port A for communication. Dynamic C uses the programming port to down-
load and debug programs.
The programming port is also used for the following operations.
• Cold-boot the Rabbit 2000 on the Intellicom after a reset.
• Remotely download and debug a program over an Ethernet connection using the
• Fast copy designated portions of flash memory from one Rabbit-based board (the
Alternate Uses of the Programming Port
All three clocked Serial Port A signals are available as
• a synchronous serial port
• an asynchronous serial port, with the clock line usable as a general CMOS input
The programming port may also be used as a serial port via the
programming cable.
In addition to Serial Port A, the Rabbit 2000 startup-mode (SMODE0, SMODE1), status,
and reset pins are available on the programming port header.
The two startup mode pins determine what happens after a reset—the Rabbit 2000 is
either cold-booted or the program begins executing at address 0x0000.
The status pin is used by Dynamic C to determine whether a Rabbit microprocessor is
present. The status output has three different programmable functions:
1. It can be driven low on the first op code fetch cycle.
2. It can be driven low during an interrupt acknowledge cycle.
3. It can also serve as a general-purpose output.
The /RESET_IN pin is an external input that is used to reset the Rabbit 2000 and the Intel-
licom onboard peripheral circuits.
Refer to the
26
RabbitLink EG2110.
master) to another (the slave) using the Rabbit Cloning Board.
Rabbit 2000 Microprocessor User’s Manual
for more information.
DIAG
Intellicom (OP6600/OP6700)
connector on the
Related parts for 20-101-0709
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: