XE8802MI035LF Semtech, XE8802MI035LF Datasheet - Page 118

• Manufacturer Part Number: XE8802MI035LF
• Description: IC DAS 16BIT FLASH 8K 100-LQFP
• Manufacturer: Semtech

Specifications of XE8802MI035LF

• Applications: Sensing Machine
• Core Processor: RISC
• Program Memory Type: FLASH (22 kB)
• Controller Series: XE8000
• Ram Size: 1K x 8
• Interface: SPI, UART
• Number Of I /o: 36
• Voltage - Supply: 2.4 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 100-LQFP
• For Use With: XE8000MP - PROG BOARD AND PROSTART2 CARD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Cont’
With:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
© Semtech 2006
OUT: (r) digital output code of the analog-to-digital converter. (MSB = OUT[15])
START: (w) setting this bit triggers a single conversion (after the current one is finished). This bit always reads back 0.
SET_NELC: (rw) sets the number of elementary conversions to 2
is chopped between elementary conversions (1,2,4,8).
SET_OSR: (rw) sets the over-sampling rate (OSR) of an elementary conversion to 2
512, 1024.
CONT: (rw) setting this bit starts a conversion. A new conversion will automatically begin as long as the bit remains at 1.
TEST: bit only used for test purposes. In normal mode, this bit is forced to 0 and cannot be overwritten.
IB_AMP_ADC: (rw) sets the bias current in the ADC to 0.25*(1+ IB_AMP_ADC[1:0]) of the normal operation current (25,
50, 75 or 100% of nominal current). To be used for low-power, low-speed operation.
IB_AMP_PGA: (rw) sets the bias current in the PGAs to 0.25*(1+IB_AMP_PGA[1:0]) of the normal operation current (25,
50, 75 or 100% of nominal current). To be used for low-power, low-speed operation.
ENABLE: (rw) enables the ADC modulator (bit 0) and the different stages of the PGAs (PGAi by bit i=1,2,3). PGA stages
that are disabled are bypassed.
FIN: (rw) These bits set the sampling frequency of the acquisition chain. Expressed as a fraction of the oscillator frequency,
the sampling frequency is given as: 00
PGA1_GAIN: (rw) sets the gain of the first stage: 0
PGA2_GAIN: (rw) sets the gain of the second stage: 00
PGA3_GAIN: (rw) sets the gain of the third stage to PGA3_GAIN[6:0]⋅1/12.
PGA2_OFFSET: (rw) sets the offset of the second stage between –1 and +1, with increments of 0.2. The MSB gives the sign
(0 → positive, 1 → negative); amplitude is coded with the bits PGA2_OFFSET[5:0].
PGA3_OFFSET: (rw) sets the offset of the third stage between –5.25 and +5.25, with increments of 1/12. The MSB gives the
sign (0 → positive, 1 → negative); amplitude is coded with the bits PGA3_OFFSET[5:0].
BUSY: (r) set to 1 if a conversion is running.
DEF: (w) sets all values to their defaults (PGA disabled, max speed, nominal modulator bias current, 2 elementary
conversions, over-sampling rate of 32) and starts a new conversion without waiting the end of the preceding one.
AMUX(4:0): (rw) AMUX[4] sets the mode (0
AMUX(3) sets the sign (0
VMUX: (rw) sets the differential reference channel (0
Default values:
Default values:
Default values:
Default values:
RegAcCfg2
RegAcCfg3
RegAcCfg4
RegAcCfg5
(r = read; w = write; rw = read & write)
Register
Name
PGA1_G
BUSY
7
0
0
0
FIN[1:0]
00
straight, 1
DEF
6
0
cross) AMUX[2:0] sets the channel.
1/4 f
PGA2_GAIN[1:0]
XE8802 Sensing Machine Data Acquisition MCU
5
RC
, 01
00
4 differential inputs, 1
1, 1
R(1) and R(0), 1
1/8 f
Bit Position
4
17-6
PGA3_OFFSET[6:0]
1, 01
PGA3_GAIN[6:0]
RC
10.
AMUX[4:0]
, 10
with ZoomingADC™ and LCD driver
0000000
0000000
00000
SET_NELC[1:0]
2, 10
3
1/32 f
PGA2_OFFSET[3:0]
RC
5, 11
R(3) and R(2)).
, 11
2
. To compensate for offsets, the input signal
7 inputs with A(0) = common reference)
0000
~8kHz.
10.
(3+SET_OSR[2:0])
1
VMUX
0
0
. OSR = 8, 16, 32, ...,
www.semtech.com