ADE7569ASTZF16 Analog Devices Inc, ADE7569ASTZF16 Datasheet - Page 123
![IC ENERGY METER MCU 16K 64LQFP](/photos/6/60/66065/505-64-lqfp_sml.jpg)
ADE7569ASTZF16
Manufacturer Part Number
ADE7569ASTZF16
Description
IC ENERGY METER MCU 16K 64LQFP
Manufacturer
Analog Devices Inc
Specifications of ADE7569ASTZF16
Applications
Energy Measurement
Core Processor
8052
Program Memory Type
FLASH (16 kB)
Controller Series
ADE75xx
Ram Size
512 x 8
Interface
I²C, SPI, UART
Number Of I /o
20
Voltage - Supply
3.135 V ~ 3.465 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LQFP
Ic Function
Single Phase Energy Measurement IC
Supply Voltage Range
3.13V To 3.46V, 2.4V To 3.7V
Operating Temperature Range
-40°C To +85°C
Digital Ic Case Style
LQFP
No. Of Pins
64
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADE7569ASTZF16
Manufacturer:
AD
Quantity:
310
Company:
Part Number:
ADE7569ASTZF16
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Company:
Part Number:
ADE7569ASTZF16-RL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Table 133. RTC Alarm Interval SFR (INTVAL, Address 0xA6)
Bit
[7:0]
Table 134. RTC Nominal Compensation SFR (RTCCOMP, Address 0xF6)
Bit
[7:0]
Table 135. RTC Temperature Compensation SFR (TEMPCAL, Address 0xF7)
Bit
[7:0]
Table 136. Interrupt Pins Configuration SFR (INTPR, Address 0xFF)
Bit
7
[6:5]
4
[3:1]
0
Table 137. Key SFR (KYREG, Address 0xC1)
Bit
[7:0]
Mnemonic
KYREG
Mnemonic
INTVAL
Mnemonic
RTCCAL
FSEL
Reserved
INT1PRG
INT0PRG
Mnemonic
RTCCOMP
Mnemonic
TEMPCAL
Default
0
Default
0
Default
0
Default
0
000
0
Default
0
Description
The TEMPCAL SFR is adjusted based on the temperature read in the TEMPADC SFR to calibrate the RTC
over temperature. This allows the external crystal shift to be compensated over temperature. This
register is retained during a watchdog reset or an external reset. It is reset after a POR.
Description
Controls the RTC calibration output. When set, the RTC calibration frequency selected by the FSEL bits
is output on the P0.2/CF1/RTCCAL pin.
Sets RTC calibration output frequency and calibration window.
FSEL
0
0
1
1
Controls the function of the INT1 pin.
INT1PRG
x
x
0
1
Controls the function of the INT0 pin.
INT0PRG
0
1
Description
The interval timer counts according to the time base established in the ITS bits of the RTC configuration SFR
(TIMECON, 0xA1). When the number of counts is equal to INTVAL, the ALARM flag is set and a pending
RTC interrupt is created. Note that the interval counter is eight bits. Therefore, it can count up to 255 seconds,
for example.
Description
Holds the nominal RTC compensation value at 25°C. This register is retained during a watchdog reset
or an external reset. It is reset after a POR.
Description
Write 0xA7 to this SFR before writing to the POWCON SFR, which unlocks KYREG.
Write 0xEA to this SFR before writing to the INTPR, HTHSEC, SEC, MIN, or HOUR timekeeping registers
to unlock KYREG.
0
0
1
1
ADE7116/ADE7156/ADE7166/ADE7169/ADE7566/ADE7569
0
1
0
1
0
1
x
x
Rev. B | Page 123 of 152
Result (Calibration Window, Frequency)
30.5 sec, 1 Hz
30.5 sec, 512 Hz
0.244 sec, 500 Hz
0.244 sec, 16 kHz
Result
GPIO
BCTRL
INT1 input disabled
INT1 input enabled
Result
INT0 input disabled
INT0 input enabled