MCP2515-I/SO Microchip Technology, MCP2515-I/SO Datasheet - Page 16

• Manufacturer Part Number: MCP2515-I/SO
• Description: IC CAN CONTROLLER W/SPI 18SOIC
• Manufacturer: Microchip Technology

Specifications of MCP2515-I/SO

• Package / Case: 18-SOIC (7.5mm Width)
• Controller Type: CAN Interface
• Interface: SPI
• Voltage - Supply: 2.7 V ~ 5.5 V
• Current - Supply: 10mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Product: Controller Area Network (CAN)
• Number Of Transceivers: 1
• Data Rate: 1 Mbps
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Supply Current (max): 10 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Supply Voltage Range: 2.7V To 5.5V
• Driver Case Style: SOIC
• No. Of Pins: 18
• Operating Temperature Range: -40°C To +85°C
• Filter Terminals: SMD
• Supply Voltage Min: 2.7V
• Rohs Compliant: Yes
• Clock Frequency: 40MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCP2515DM-BM - BOARD DEMO FOR MCP2515/51MCP2515DM-PTPLS - BOARD DAUGHTER PICTAIL MCP2515MCP2515DM-PCTL - BOARD DEMO FOR MCP2515DV251001 - KIT DEVELOPMENT CAN MCP2510
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

MCP2515
3.5
The TXnRTS pins are input pins that can be configured
as:
• Request-to-send inputs, which provides an
• Standard digital inputs
Configuration and control of these pins is accomplished
using the TXRTSCTRL register (see Register 3-2). The
TXRTSCTRL register can only be modified when the
MCP2515 is in Configuration mode (see Section 10.0
“Modes of Operation”). If configured to operate as a
request-to-send pin, the pin is mapped into the
respective TXBnCTRL.TXREQ bit for the transmit
buffer. The TXREQ bit is latched by the falling edge of
the TXnRTS pin. The TXnRTS pins are designed to
allow them to be tied directly to the RXnBF pins to
automatically initiate a message transmission when the
RXnBF pin goes low.
The TXnRTS pins have internal pull-up resistors of
100 k (nominal).
DS21801C-page 16
alternative means of initiating the transmission of
a message from any of the transmit buffers
TXnRTS PINS
Preliminary
3.6
The MCU can request to abort a message in a specific
message
TXBnCTRL.TXREQ bit.
In addition, all pending messages can be requested to
be aborted by setting the CANCTRL.ABAT bit. This bit
MUST be reset (typically after the TXREQ bits have
been verified to be cleared) to continue transmitting
messages. The CANCTRL.ABTF flag will only be set if
the abort was requested via the CANCTRL.ABAT bit.
Aborting a message by resetting the TXREQ bit does
NOT cause the ABTF bit to be set.
Note:
Aborting Transmission
Messages that are currently transmitting
when the abort was requested will
continue to transmit. If the message does
not successfully complete transmission
(i.e., lost arbitration or was interrupted by
an error frame), it will then be aborted.
buffer
by
 2004 Microchip Technology Inc.
clearing
the
associated