CY7C68300C-56PVXC Cypress Semiconductor Corp, CY7C68300C-56PVXC Datasheet - Page 25

• Manufacturer Part Number: CY7C68300C-56PVXC
• Description: IC USB 2.0 BRIDGE AT2LP 56-SSOP
• Manufacturer: Cypress Semiconductor Corp
• Series: CY7Cr
• Type: USB to ATA/ATAPI Bridger

Specifications of CY7C68300C-56PVXC

• Package / Case: 56-SSOP
• Controller Type: USB 2.0 Controller
• Interface: I²C
• Voltage - Supply: 3.15 V ~ 3.45 V
• Current - Supply: 50mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Number Of Bits: 48
• Operating Temperature Range: 0 C to + 70 C
• Supply Current: 10 mA
• Operating Supply Voltage: 3.3 V
• Controller Family/series: (8051) USB
• Core Size: 8 Bit
• No. Of I/o's: 6
• Embedded Interface Type: I2C, USB
• Digital Ic Case Style: SSOP
• Supply Voltage Range: 3V To 3.6V
• Rohs Compliant: Yes
• Operating Temperature (min): 0C
• Operating Temperature Classification: Commercial
• Operating Temperature (max): 70C
• Package Type: SSOP
• Rad Hardened: No
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: CY4615B - KIT USB TO ATA REFERENCE DESIGN
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 428-2266-5; CY7C68300C-56PVXC

Table 11. Configuration Data Organization (continued)
Document 001-05809 Rev. *B
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
Address
Byte
Reserved
General Purpose I/O Pin
Output Enable
Reserved
GPIO Output Pin State
LUN0 Identify String
LUN1 Identify String
Delay After Reset
Reserved
Bus-Powered Flag
CF UDMA Enable
Fixed Number of Logical
Configuration
Item Name
Bits 7:6
Reserved. Must be set to zero.
Bits 5:0
GPIO[5:0] Input and output control. GPIOs can be individ-
ually set as inputs or outputs using these bits.
0 = Hi-Z (pin is an input). The state of the signal connected
to GPIO input pins is reported in the SYSIRQ or HID data.
1 = Output enabled (pin is an output). The state of GPIO
output pins is controlled by the value in address 0x0A.
Bits 7:6
Reserved. Must be set to zero.
Bits 5:0
These bits select the value driven on the GPIO pins that are
configured as outputs in configuration address 0x09.
0 = Drive the GPIO pin LOW
1 = Drive the GPIO pin HIGH
This byte is a pointer to the start of a 24 byte ASCII
(non-Unicode) string in the EEPROM that is used as the
LUN0 device identifier. This string is used by many operating
systems as the user-visible name for the drive. If this byte is
0x00, the Identify Device data from the drive is used instead.
This byte is a pointer to the start of a 24 byte ASCII
(non-Unicode) string in the EEPROM that is used as the
LUN1 device identifier. This string is used by many operating
systems as the user-visible name for the drive. If this byte is
0x00, the Identify Device data from the drive is used instead.
Number of 20-ms ticks to wait between AT2LP startup or
reset, and the first attempt to access any drives.
Bits 7:5
Must be set to zero.
Bit 4
Enable bus-powered HDD support. This bit enables the use
of DRVPWRVLD features without reporting the LUN0 device
as removable media.
0 = LUN0 is removable media or DRVPWRVLD is disabled
1 = LUN0 device is bus-powered and non-removable
Bit 3
Enable UDMA transfers for removable devices. Some CF
devices interfere with UDMA transfers when more than one
drive is connected to the ATA bus.
0 = Do not use UDMA transfers with removable devices
(UDMA signals are not connected to the CF pins).
1 = Allow UDMA transfers to be used with removable
devices (UDMA signals are connected to the CF pins).
Bits 2:1
Assume the presence of devices and do not perform a
search of the ATA bus to discover the number of LUNs.
00 = Search ATA bus and determine number of LUNs
01 = Assume only LUN0 present; no ATA bus search
10 = Assume LUN0 and LUN1 present; no ATA bus search
11 = Assume LUN0 and LUN1 present; no ATA bus search
Item Description
Configuration
CY7C68300C, CY7C68301C
CY7C68320C, CY7C68321C
Required
Contents
Contents
Variable
Page 25 of 42
0x00
0x00
0x00
0x00
0x00
0x00
[+] Feedback